Engine Cranks But Does Not Run
Engine Cranks but Does Not Run
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Initial Inspection and Diagnostic Overview) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Initial Inspection and Diagnostic Overview) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Initial Inspection and Diagnostic Overview) provides an overview of each diagnostic category.
Circuit/System Description
This Engine Cranks but Does Not Run is an organized approach to identify a condition which causes the engine to crank but not start. This diagnostic directs the technician to the appropriate system diagnosis.
This diagnostic assumes the system voltage levels are adequate for starter motor operation. Fuel level and fuel quality must be determined for correct diagnosis.
Reference Information
Schematic Reference
Engine Controls Schematics (Electrical Diagrams)
Connector End View Reference
Component Connector End Views (Connector Views)
Electrical Information Reference
* Battery Inspection/Test (Battery Inspection/Test)
* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Electrical Center Identification Views (Application and ID)
* Engine Cranks Slowly (Engine Cranks Slowly)
* Starting System Description and Operation (Description and Operation)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (Diagnostic Trouble Code Descriptions)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Special Tools
* CH-48027 Digital Press Gage
* J 26792 HEI Spark Tester
Circuit/System Verification
Attempt to start the engine. Engine should start and run.
Circuit/System Testing
1. Crank the engine for up to 30 seconds.
2. Observe the vehicle DTC information with a scan tool.
• If any of the following DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (Diagnostic Trouble Code Descriptions) : P0201-P0206, P0335, P0336, P0351-P0353, P0601, P0602, P0604, P0685, P1516, P2610.
3. Observe the engine speed parameter while cranking the engine.
• If engine RPM is not indicated, refer to DTC P0335 (P0335).
4. Install a J 26792 HEI Spark Tester.
5. Crank the engine for 15 seconds. Spark should be observed from the J 26792 HEI Spark Tester.
• If spark is not observed refer to Electronic Ignition (EI) System Diagnosis (Electronic Ignition (EI) System Diagnosis).
6. With the ignition ON and the engine OFF, test the fuses that are supplied by the powertrain relay for voltage.
• If the test lamp does not illuminate on at least one side of each fuse refer to DTC P0685 (P0685).
Important: Additional DTCs may set when using the fuel pump output control.
7. Command the fuel pump ON and OFF. Fuel pump should energize when commanded ON, and de-energize when commanded OFF.
• If the fuel pump does not respond, refer to Fuel Pump Electrical Circuit Diagnosis (Component Tests and General Diagnostics).
8. Turn OFF the ignition.
9. Install the CH-48027 Digital Pressure Gage. Turn ON the ignition and command the fuel pump ON while observing the CH-48027. The fuel pressure should be between 384-425 kPa (56-62 psi).
• If the fuel pressure is not within 384-425 kPa (56-62 psi), refer to Fuel System Diagnosis (Component Tests and General Diagnostics).
10. Inspect for the following conditions:
* Compare the actual engine coolant temperature to the ECT parameter.
* Air filter and air intake system for restrictions and obstructions
* Test the fuel for contamination. Refer to Alcohol/Contaminants-in-Fuel Diagnosis (With Special Tool) (Alcohol/Contaminants-In-Fuel Diagnosis (With Special Tool)).
* Inspect the spark plug and spark plug wires. Refer to Spark Plug Wire Inspection (Testing and Inspection) and Spark Plug Inspection (Testing and Inspection).
* Test the exhaust system for restrictions. Refer to Restricted Exhaust (Restricted Exhaust).
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Spark Plug Replacement (Service and Repair)
* Spark Plug Wire Replacement (Service and Repair)