B0081
DTC B0081
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Initial Inspection and Diagnostic Overview) prior to using this diagnostic procedure.
* ReviewStrategy Based Diagnosis (Initial Inspection and Diagnostic Overview) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Initial Inspection and Diagnostic Overview) provides an overview of each diagnostic category.
DTC Descriptors
DTC B0081 0F
- Passenger Presence System Erratic
DTC B0081 39
- Passenger Presence System Internal Electronic Failure
DTC B0081 3A
- Passenger Presence System Incorrect Component Installed
DTC B0081 71
- Passenger Presence System Invalid Serial Data Received
Circuit/System Description
When the ignition is turned ON, the passenger presence system (PPS) and the inflatable restraint sensing and diagnostic module (SDM) performs tests to diagnose critical malfunctions within itself. When the SDM has completed the power-up mode, the SDM will establish communication with the PPS. The SDM will also request the instrument panel cluster to illuminate both of the PASSENGER AIR BAG ON/OFF indicators ON for 5 seconds. If the SDM detects that the PPS has set a current DTC, the SDM will then disable the instrument panel (I/P) module deployment loop, set DTC B0081, and illuminate the AIR BAG indicator.
Conditions for Running the DTC
Ignition voltage is between 9-16 volts.
Conditions for Setting the DTC
Any of the following conditions must exist for 5 seconds:
B0081 0F
* The SDM has received a fault present message from the PPS.
* The PPS is in assembly plant mode and the SDM is in production mode.
B0081 39
The SDM has received a fault message from the PPS.
B0081 3A
The SDM has received a message from the PPS indicating a vehicle and PPS mismatch.
B0081 71
The SDM has received invalid or no serial data from the PPS.
Action Taken When the DTC Sets
* The SDM requests the instrument panel cluster (IPC) to illuminate the AIR BAG indicator.
* The I/P module deployment loop will be disable.
Conditions for Clearing the DTC
* The condition for setting the DTC no longer exists.
* A history DTC will clear once 100 malfunction-free ignition cycles have occurred.
Diagnostic Aids
If either the SDM or PPS were replaced, verify that the correct part numbers were used for the vehicle application.
Reference Information
Schematic Reference
SIR Schematics (SIR Schematics)
Connector End View Reference
Component Connector End Views (Connector Views)
Description and Operation
SIR System Description and Operation (Description and Operation)
Electrical Information Reference
* Circuit Testing (Component Tests and General Diagnostics)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Circuit/System Verification
Important: A DTC B0081 set in history may not clear until the PPS module enters the sleep mode. When removing connectors inspect for damage, corrosion or poor connection. Damage or corrosion in the following requires repair or replacement of the affected component/connector.
* PPS module
* SDM module
* PPS module harness connector
* SDM wiring harness connector
1. Ignition ON, retrieve DTCs from the PPS.
2. Verify that DTC B0081 3A is not set as current.
• If DTC B0081 3A is current, replace the PPS with the correct part number.
3. Verify DTC B0081 39 is not set as current.
• If DTC B0081 39 is current, replace the PPS.
4. Verify DTC B1000, B1001, or U0170 is not set as current.
• If DTC B1000, B1001, or U0170 is current, Refer to Diagnostic Trouble Code (DTC) List - Vehicle (Diagnostic Trouble Code Descriptions).
5. Verify DTC B0081 71 or B0081 0F is not set.
• If DTC B0081 71 or B0081 0F is set, clear the SDM DTCs. No other repairs are necessary.
Clearing DTC B0081
1. To enter the sleep mode, remove the scan tool, turn the ignition OFF, open and close the driver door.
2. With the ignition OFF and all doors closed, wait 30 seconds.
3. Clear DTC B0081. The DTC should now be cleared.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* SIR/SRS Wiring Repairs (Component Tests and General Diagnostics)
* Control Module References (Programming and Relearning) for PPS and SDM replacement, setup, and programming