Electronic Brake and Traction Control Module with Brake Pressure Modulator Valve Replacement

Electronic Brake and Traction Control Module with Brake Pressure Modulator Valve Replacement

Removal Procedure
Warning: Refer to Brake Fluid Irritant Warning (Brake Fluid Irritant Warning).


Caution: Refer to Brake Fluid Effects on Paint and Electrical Components Caution (Brake Fluid Effects on Paint and Electrical Components Caution).

Caution: To prevent equipment damage, never connect or disconnect the wiring harness connection from the EBCM with the ignition switch in the ON position.

1. Remove the battery tray. Refer to Battery Tray Replacement (Service and Repair).
2. Disconnect the brake fluid level sensor electrical connector.
3. Without draining the coolant and without disconnecting the hoses, remove and position aside the radiator surge tank. Refer to Radiator Surge Tank Replacement (Radiator Surge Tank Replacement).
4. Thoroughly clean the electronic brake control module (EBCM) to brake pressure modulator valve (BPMV) area of any accumulated dirt and debris.
5. Disconnect the EBCM electrical connector.




6. Disconnect the master cylinder primary brake pipe fitting (1).
7. Cap the brake pipe fitting and plug the BPMV inlet port to prevent brake fluid loss and contamination.
8. Disconnect the master cylinder secondary brake pipe fitting (2).
9. Cap the brake pipe fitting and plug the BPMV inlet port to prevent brake fluid loss and contamination.




10. Disconnect the right front brake pipe fitting (1).
11. Cap the brake pipe fitting and plug the BPMV outlet port to prevent brake fluid loss and contamination.
12. Disconnect the left front brake pipe fitting (2).
13. Cap the brake pipe fitting and plug the BPMV outlet port to prevent brake fluid loss and contamination.




14. Disconnect the left rear brake pipe fitting (1).
15. Cap the brake pipe fitting and plug the BPMV outlet port to prevent brake fluid loss and contamination.
16. Disconnect the right rear brake pipe fitting (2).
17. Cap the brake pipe fitting and plug the BPMV outlet port to prevent brake fluid loss and contamination.




18. Remove the electronic brake and traction control module with brake pressure modulator valve assembly nuts (1).




19. Remove the electronic brake and traction control module with brake pressure modulator valve assembly bolt (1).
20. Remove the electronic brake and traction control module with brake pressure modulator valve assembly.




21. Remove the electronic brake and traction control module with brake pressure modulator valve assembly bracket bolts (1).
22. Remove the EBCM. Refer to Electronic Brake Control Module Replacement (Electronic Brake Control Module Replacement).

Installation Procedure

1. Install the EBCM. Refer to Electronic Brake Control Module Replacement (Electronic Brake Control Module Replacement).





Caution: Refer to Fastener Caution (Fastener Caution).

2. Install the electronic brake and traction control module with brake pressure modulator valve assembly bracket bolts (1) and tighten to 10 Nm (89 lb in).




3. Install the electronic brake and traction control module with brake pressure modulator valve assembly.
4. Install the electronic brake and traction control module with brake pressure modulator valve assembly bolt (1) and tighten to 20 Nm (15 lb ft).




5. Install the electronic brake and traction control module with brake pressure modulator valve assembly nuts (1) and tighten to 20 Nm (15 lb ft).




6. Install the left rear brake pipe fitting (1) and tighten to 18 Nm (13 lb ft).
7. Install the right rear brake pipe fitting (2) and tighten to 18 Nm (13 lb ft).




8. Install the right front brake pipe fitting (1) and tighten to 18 Nm (13 lb ft).
9. Install the left front brake pipe fitting (2) and tighten to 18 Nm (13 lb ft).




10. Install the master cylinder primary brake pipe fitting (1) and tighten to 18 Nm (13 lb ft).
11. Install the master cylinder secondary brake pipe fitting (2) and tighten to 18 Nm (13 lb ft).
12. Connect the EBCM electrical connector.
13. Install the radiator surge tank. Refer to Radiator Surge Tank Replacement (Radiator Surge Tank Replacement).
14. Connect the brake fluid level sensor electrical connector.
15. Install the battery tray. Refer to Battery Tray Replacement (Service and Repair).
16. Program the EBCM. Refer to Control Module References (Programming and Relearning).
17. Bleed the antilock brake system. Refer to Antilock Brake System Automated Bleed (Antilock Brake System Automated Bleed).
18. Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle).
19. Calibrate the brake pedal position sensor. Refer to Brake Pedal Position Sensor Calibration ().
20. Center the steering angle sensor. Refer to Steering Angle Sensor Centering (Procedures).