P0175

CIRCUIT DESCRIPTION
While in Closed Loop, the Engine Control Module (ECM) monitors the Heated Oxygen Sensor (HO2S) signal voltage and adjusts the fuel delivery based on the signal voltage. A change made to fuel delivery will be indicated by the Long and Short Term Fuel Trim values. The Short Term Fuel Trim values change rapidly in response to the HO2S signal voltages. These changes fine tune the engine fueling. The Long Term Fuel Trim values change in response to trends in the Short Term Fuel Trim. The Long Term Fuel Trim makes coarse adjustments to the fueling in order to re-center and restore control to the Short Term Fuel Trim. The Short and the Long Term Fuel Trim can be monitored with a scan tool. Ideal fuel trim values are around 0 percent. A positive fuel trim value indicates that the ECM is adding fuel in order to compensate for a lean condition. A negative fuel trim value indicates that the ECM is reducing the amount of fuel in order to compensate for a rich condition. If an excessively rich or lean condition is detected, the ECM will set a Diagnostic Trouble Code (DTC). The Long Term Fuel Trim diagnostic parameter is an average of several of the long term speed load learn cells which the ECM selects based on the engine speed and the engine load.

CONDITIONS FOR RUNNING THE DTC
^ Closed Loop operation
^ Fuel trim enabled

CONDITIONS FOR SETTING THE DTC
The ECM detects the average Long Term Fuel Trim cell values are below a predetermined threshold.

ACTION TAKEN WHEN THE DTC SETS
^ The ECM illuminates the Malfunction Indicator Lamp (MIL) on the second consecutive drive trip that the diagnostic runs and fails if the diagnostic fails under the same conditions, the load, the RPM, the temperature, as the previous ignition cycle that the test ran and failed.
^ The first drive trip that this diagnostic fails, Fail Pending, this information will be stored in the Freeze Frame. Any data that was previously stored in the Freeze Frame will be overwritten by the Freeze Frame data for this DTC. The only exception to this is if a Misfire DTC was already recorded in the Freeze Frame. In this case, the misfire data stays in the Freeze Frame and the fuel trim data is not stored.

CONDITIONS FOR CLEARING THE MIL/DTC

IMPORTANT: If the last failure was during a non-typical driving condition, the MIL may remain ON more than three drive trips. Review the Freeze Frame for the last failure conditions.

^ The ECM turns OFF the MIL after three consecutive drive trips that the diagnostic runs and does not fail within the same conditions that the DTC last failed.
^ A History DTC clears after forty consecutive warm-up cycles if no failures report by this diagnostic or any other emission related diagnostic.
^ The scan tool clears the MIL/DTC.

DIAGNOSTIC AIDS
In terms of fuel trim a value less than -8.5 percent would be -9.0 percent which indicates the ECM is leaning the fuel mixture. (Taking fuel away to compensate for a Rich condition). A positive value indicates the ECM is richening the fuel mixture. (Adding more fuel to compensate for a Lean condition). If using the diagnostic table does not isolate the problem, try monitoring the Long Term Fuel Trim cell while operating the vehicle under various loads. Monitor the engine data list for the possibility of a skewed sensor causing a driveability concern. This may isolate the condition which caused the setting of the current DTC. IF DTC P0175 and P0172 are both set, inspect the fuel pressure regulators atmospheric vent hose for signs of fuel. The vent hose connects to the bottom side of the throttle body. If the fuel pressure regulator has failed the engine will burn the excess fuel causing a rich condition. A fault in the EVAP system could also cause a rich condition. Inspect the EVAP system for proper operation. Use the J 35616-A connector test adapter kit for any test that requires probing the ECM harness connector or a component harness connector. Using this kit prevents damage to the harness or component terminals. Refer to Using Connector Test Adapters in Diagrams. For an intermittent, refer to Symptoms. If a repair is necessary refer to Wiring Repairs or Connector Repairs in Diagrams. Symptom Related Diagnostic Procedures

TEST DESCRIPTION

Steps 1 - 7:

Steps 8 - 9:

The numbers below refer to the step numbers on the diagnostic table.
2. This step determines if the fault is present
3. This process may help in order to recreate the malfunction.
4. This step determines if both banks are running rich.
5. This step addresses areas of concern that could cause both banks of the engine to run rich.