P0451
DTC P0451 - FUEL TANK PRESSURE (FTP) SENSOR PERFORMANCECIRCUIT DESCRIPTION
The control module monitors the fuel tank pressure (FTP) sensor signal in order to detect vacuum decay and excess vacuum during the evaporative emission (EVAP) diagnostic test. The control module supplies a 5-voltreference and a low reference circuit to the FTP sensor. This DTC sets if the engine control module (ECM) detects one of the following conditions:
- The FTP sensor signal voltage is not within a calibrated range on a cold start-up.
- The FTP sensor signal does not change by a calibrated amount when purge is active.
- The FTP sensor signal oscillates more than a calibrated amount when vehicle speed is less than 30 km/h (50 mph).
The table illustrates the relationship between FTP sensor signal voltage and the EVAP system pressure/vacuum.
DTC DESCRIPTOR
This diagnostic procedure supports the following DTC.
DTC P0451 Fuel Tank Pressure (FTP) Sensor Performance
CONDITIONS FOR RUNNING THE DTC
- The fuel level is between 15-85 percent.
- The start up engine coolant temperature (ECT) is less than 35°C (95°F).
- The vehicle speed is less than 30 km/h (50 mph).
- The ECM is commanding purge.
- The ratio between ambient pressure and the calculated manifold pressure is less than 0.6.
CONDITIONS FOR SETTING THE DTC
- The ECM detects that the FTP sensor voltage on a cold start-up is less than 0.3 volts or more than 2.95 volts for 25 seconds.
- The ECM does not detect a change in tank vacuum when purge duty cycle is more than 40 percent. The change in vacuum must be less than -6.0 kPa (-0.25 inches H2O) when purge is active. This condition requires 3 failures to set the DTC for 10 seconds each time.
- The ECM detects that the FTP sensor signal oscillates more than +/- 0.85 volts from a zero point for 25 seconds. For example, 1.5 volts = 0pressure/vacuum change, the signal should not oscillate more than +/- 0.85 volts from this zero point. The zero point may vary between 1.0-2.5 volts. The vehicle speed must be less than 30 km/h (50 mph)for this test.
ACTION TAKEN WHEN THE DTC SETS
- The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
- The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.
CONDITIONS FOR CLEARING THE MIL/DTC
- The malfunction indicator lamp (MIL) will turn OFF after 3 consecutive ignition cycles in which the diagnostic runs without a fault.
- A history DTC will clear after 40 consecutive warm-up cycles without a fault.
- Clear the DTCs with a scan tool.
DIAGNOSTIC AIDS
- Use the J 35616-B Connector Test Adapter Kit for any test that requires probing the ECM harness connector or a component harness connector.
- The lower connector of the ECM is connector C1 and the upper connector of the ECM is connector C2. Refer to Computers and Control Systems Component Views.
- A blocked or clogged EVAP canister vent may set this DTC.
- For an intermittent condition, refer to Intermittent Conditions. Diagnostic Strategies
TEST DESCRIPTION
Steps 1-3:
Steps 4-6:
Steps 7-10:
Steps 11-16:
The numbers below refer to the step numbers on the diagnostic table.
2. This step verifies that the condition is present.
4. The ECM produces a measurable steady state amperage that provides the 5-volt reference to the FTP sensor. If the amperage on the 5-voltreference circuit is less than 80 mA, test the 5-volt reference circuit for an open or high resistance.
5. This step tests the signal circuit of the FTP sensor.