Remote Control Door Lock and Theft Deterrent Transmitter Programming (with Y41 - Canada and Europe)
Remote Control Door Lock and Theft Deterrent Transmitter Programming (with Y41 - Canada and Europe)
Note: Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This will prevent the programming of the transmitters to the incorrect vehicle.
There are 2 methods for programming keyless entry transmitters. Up to 4 transmitters may be programmed to the remote control door lock receiver (RCDLR). Each programmed transmitter is given a position of #1-#4 in the RCDLR memory.
The transmitter with #1 on top of it must be programmed first, and transmitter with #2 on top of it must be programmed second; either transmitter may be programmed as the third or fourth transmitter. If replacing a transmitter, ensure that the proper transmitter with the correct number on top of it gets ordered.
A "known" transmitter is one that has already been programmed to the vehicle. It is very important that the transmitter which is to be programmed is NOT placed into the console transmitter pocket until the DIC correctly displays the transmitter number that you wish to program to.
Method 1 - Adding, Replacing, or Invalidating Transmitters (Known Transmitter Available)
This procedure will add or replace transmitters. This procedure requires that you have two known transmitters available, a replacement transmitter, and a scan tool.
Method 1 is also used for the initial programming of transmitters to a new replacement RCDLR. In this instance, the new RCDLR comes ready to learn the first transmitters introduced. Perform the learn procedure as outlined, with the exception that the new RCDLR does not require a known transmitter be placed within the interior of the vehicle.
Note: This procedure is not available when the maximum number of transmitters (4) have been programmed. If 4 transmitters are programmed to this RCDLR and this method is attempted, the driver information center (DIC) will display MAXIMUM # ELECTRONIC KEYS LEARNED and the programming procedure will exit. Method 2 must be used in this instance.
1. The vehicle must be OFF.
2. Place two known transmitters and any new transmitter(s) to be programmed in the cupholder inside the vehicle. DO NOT PLACE ANY TRANSMITTERS IN THE CONSOLE POCKET AT THIS TIME.
3. Use scan tool to access the following:
* Vehicle Control Systems
* Computer/Integrating Systems
* Module Setup
* Remote Control Door Lock Receiver
* Program Key Fobs
4. Select the transmitter position you wish to program:
Note: Selecting Invalidate All transmitters will erase any known transmitters and will cause the DIC to prompt READY FOR transmitter 1, requiring all transmitters to be relearned to the vehicle.
* Invalidate All transmitters
* Next Available Slot
* Program Key Fob 1
* Program Key Fob 2
* Program Key Fob 3
* Program Key Fob 4
5. After making the selection, a beep should be heard. If a beep is not heard or the DIC displays ELECTRONIC KEY NOT DETECTED, a valid transmitter was not found. Ensure that a valid transmitter has been placed in the cupholder and repeat step 4.
6. The scan tool will be displaying the current transmitter programming status. Press the PROGRAM soft key on the scan tool to continue with programming. The DIC should respond by displaying: READY TO LEARN ELECTRONIC KEY #X (X = 1, 2, 3 or 4, depending on the selected position).
7. With the DIC displaying the correct transmitter position that is to be programmed, place the new/replacement transmitter in the console pocket with the buttons facing forward.
8. A beep will occur once the transmitter has been learned.
9. Depending on the option chosen above, the DIC may display a prompt asking that another transmitter be programmed. If programming additional transmitters, repeat steps 6 and 7, or press the EXIT soft key on the scan tool.
Note: Newly programmed transmitters will not function until program mode has been exited (DIC is blank). This must be done prior to pressing the UNLOCK button in the next step.
10. Press the UNLOCK button on each transmitter that was programmed to finalize the programming and confirm system operation.
Method 2 - Service Programming System Transmitter Programming
This procedure is a 10-minute relearn procedure using the Techline Terminal with SPS software. Once the 10-minute timer has expired, the transmitters can be programmed to particular positions or all known transmitters can be erased. A scan tool, Techline Terminal, and a replacement transmitter are required to perform this procedure.
1. Ignition ON, connect a scan tool to the vehicle in the pass-thru arrangement.
2. Insure that all power consuming devices are turned OFF on the vehicle.
3. On the Techline Terminal, select Service Programming System and follow the Techline Terminal on-screen instructions, using the Legacy Pass-Thru method. Select "VTD Vehicle Theft Deterrent Learn" under Component Replacement. Ensure that "Prepare RCDLR for transmitter programming" is used.
4. At this point the scan tool must remain connected for the duration of the 10 minute relearn procedure.
5. When the 10 minute relearn procedure has completed, turn the vehicle OFF.
6. With the scan tool still connected, access the following:
* Vehicle Control Systems
* Computer/Integrating Systems
* Module Setup
* Remote Control Door Lock Receiver
* Program Key Fobs
7. Select the transmitter position you wish to program:
Note: Selecting Invalidate All transmitters will erase any known transmitters and will cause the DIC to prompt READY FOR transmitter 1, requiring all transmitters to be relearned to the vehicle.
* Invalidate All transmitters
* Next Available Slot
* Program Key Fob 1
* Program Key Fob 2
* Program Key Fob 3
* Program Key Fob 4
8. After making the selection, a beep should be heard. If a beep is not heard or the DIC displays ELECTRONIC KEY NOT DETECTED, a valid transmitter was not found. Ensure that a valid transmitter has been placed in the cupholder and repeat step 4.
9. The scan tool will be displaying the current transmitter programming status. Press the PROGRAM soft key on the scan tool to continue with programming. The DIC should respond by displaying: READY TO LEARN ELECTRONIC KEY #X (X = 1, 2, 3 or 4, depending on the selected position).
10. With the DIC displaying the correct transmitter position that is to be programmed, place the new/replacement transmitter in the console pocket with the buttons facing forward.
11. A beep will occur once the transmitter has been learned.
12. Depending on the option chosen above, the DIC may display a prompt asking that another transmitter be programmed. If programming additional transmitters, repeat steps 9 and 10, or press the EXIT soft key on the scan tool.
Note: Newly programmed transmitters will not function until program mode has been exited (DIC is blank). This must be done prior to pressing the UNLOCK button in the next step.
13. Press the UNLOCK button on each transmitter that was programmed to finalize the programming and confirm system operation.