B2494
Liftgate Handle Switch Malfunction - DTC B2494
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptor
DTC B2494 02
-
Liftgate Handle Switch Circuit Short to Ground
Diagnostic Fault Information
Circuit/System Description
The power liftgate handle switch circuit provides a single input to the liftgate control module. The liftgate handle switch is supplied a signal voltage, when the switch contact closes and the voltage drops, the liftgate control module detects the voltage drop and commands the liftgate to release.
Conditions for Running the DTC
The system voltage is 9-16 V.
Conditions for Setting the DTC
The liftgate handle switch signal circuit is active for greater than 30 seconds.
Action Taken When the DTC Sets
The liftgate control module will ignore the signal from the liftgate handle switch. Normal power liftgate operation will be available from the interior liftgate control switch or from a request from the remote keyless entry module.
Conditions for Clearing the DTC
* The DTC will be current for as long as the fault is present.
* When the fault is no longer present, the DTC will be a history DTC.
* A history DTC will clear after 50 ignition cycles.
Diagnostic Aids
* If the liftgate will not release from the closed position, refer to Opening the Liftgate Without Electrical Power Procedures for the appropriate procedure
* Whenever the liftgate control module loses power or is disconnected, the ignition must be cycled OFF then ON in order to reactivate the liftgate control module.
* An intermittent short to ground in the Rear Liftgate Open/Close Switch circuit may cause the liftgate control module to command the liftgate to open if the vehicle is in park and the doors are unlocked. If the vehicle has a history of the liftgate opening unexpectedly, inspect the point where the wires enter the exterior liftgate handle switch for corrosion or evidence of water intrusion.
Reference Information
Schematic Reference
Liftgate Schematics Liftgate Schematics
Connector End View Reference
Component Connector End Views A/C Compressor Clutch
Description and Operation
Liftgate Description and Operation Liftgate
Electrical Information Reference
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Circuit Testing Circuit Testing
* Wiring Repairs Wiring Repairs
* Connector Repairs Connector Repairs
Scan Tool Reference
Control Module References Control Module References for scan tool information
Circuit/System Verification
1. DTC B2494 should not be set as a history DTC.
• If DTC B2494 is set only as history, replace the S45A liftgate handle switch-exterior.
2. Ignition ON, observe the scan tool Liftgate Handle Sw. parameter while pressing and releasing the liftgate handle switch-exterior. The parameter should change between Active and Inactive.
Circuit/System Testing
1. Ignition OFF, disconnect the X903 inline harness connector at the S45A liftgate handle switch-exterior.
2. Test for less than 10 ohms between the low reference circuit terminal 2 and ground.
• If greater than the specified range, test the low reference circuit terminal for a short to voltage or an open/high resistance. If the circuit tests normal, replace the K39 liftgate control module.
3. Ignition ON, verify the scan tool Liftgate Handle Sw. parameter is Inactive.
• If not the specified value, test the signal circuit terminal 7 for a short to ground. If the circuit tests normal, replace the K39 liftgate control module.
4. Connect a 3 A fused jumper wire between the signal circuit terminal 7 and ground, verify the scan tool Liftgate Handle Sw. parameter is Active.
• If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the K39 liftgate control module.
5. If all circuits test normal, test or replace the S45A liftgate handle switch-exterior.
Component Testing
1. Ignition OFF, disconnect the X903 inline harness connector at the S45A liftgate handle switch-exterior
2. Test for infinite resistance between the signal circuit terminal 7 and the low reference circuit terminal 2 with the switch in the open position.
• If not the specified value, replace the S45A liftgate handle switch-exterior.
3. Test for less than 2 ohms between the signal circuit terminal 7 and the low reference circuit terminal 2 with the switch in the closed position.
• If greater than the specified range, replace the S45A liftgate handle switch-exterior.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the diagnostic repair.
* Rear License Plate Lamp Wiring Harness Replacement (Wagon) Rear License Plate Lamp Wiring Harness Replacement (Wagon)Rear License Plate Lamp Wiring Harness Replacement (Sedan/Coupe) Rear License Plate Lamp Wiring Harness Replacement (Sedan/Coupe)
* Control Module References Control Module References for liftgate control module replacement, setup and programming