Trim Height Inspection (GNB)
Trim Height Inspection (GNB)
Trim Height Measurement
Trim height is a predetermined measurement relating to vehicle ride height. Incorrect trim heights can cause the vehicle to bottom out over bumps, damage to the suspension components and symptoms similar to wheel alignment problems. Check the trim heights when diagnosing suspension concerns and before checking the wheel alignment.
Perform the following before measuring the trim heights:
* Run the engine until the auto leveling compressor shuts off and then roll the vehicle on to a flat surface.
* Set the tire pressure to the specifications shown on the certification label. Refer to Vehicle Certification, Tire Placard, Anti-Theft, and Service Parts ID Label Vehicle Certification, Tire Placard, Anti-Theft and Service Parts ID Label.
* Check the fuel level. Add additional weight if necessary to simulate a full tank.
* Make sure the passenger and rear compartments are empty, except for the spare tire.
* Make sure the vehicle is on a flat and level surface, such as an alignment rack.
* Check that all the vehicle doors are securely closed.
* Check that the vehicle hood and rear deck lids are securely closed.
* Check for installed after market accessories or modifications that could affect trim height measurement:
- Larger or Smaller than production wheels and tires.
- Lifting or Lowering Kits
- Wheel Opening Flares or Ground Affects
Measuring the P and R Dimension
Measurement Definitions
P Height: The vertical distance from the ground to the top of the wheel opening through the center line of the front wheel.
R Height: The vertical distance from the ground to the top of the wheel opening through the center line of the rear wheel.
Use the following procedures to measure the P and R dimensions:
1. Use the following procedure to measure the P R dimensions.
Note: The left and right P and R height differences should be no more than 10 mm (.39 in).
2. Push the front bumper down a minimum of 25 mm (1 in), and release. Perform this step three times.
3. Measure and record the trim height per the "Measurement Definitions" above.
4. Lift the bumper up a minimum of 25 mm (1 in), and release. Perform this step three times.
5. Measure and record the trim height per the "Measurement Definitions" above.
6. The true P height measurement is the average of the measurements taken in step 2 & 4. Refer to Trim Height Specifications Trim Height Specifications
7. Repeat the above steps at the rear of the vehicle for the R heights.
8. If the P & R heights are outside of the specifications, measure the Z & D heights.
Modified R Height:
This is for checking the vehicles equipped with air suspension system to remove the tire size out of the measurement. Measure the vertical distance from the center of the wheel to the top of the wheel opening.
Note: The left and right R height differences should be no more than 10 mm (.39 in).
1. Push the front bumper down a minimum of 25 mm (1 in), and release. Perform this step three times.
2. Measure and record the trim height per the "Measurement Definitions" above.
3. Lift the bumper up a minimum of 25 mm (1 in), and release. Perform this step three times.
4. Measure and record the trim height per the "Measurement Definitions" above.
5. The modified R height measurement should be 406.7 mm (16 in)
6. If the R heights are outside of the specifications, measure the Z & D heights.
Measuring the Z Dimension
Measurement Definitions
Z Height: The vertical distance between the bottom surface of the cradle bracket (2) in line with the outer measurement and the lowest point on the surface of the lower control arm at the knuckle (1).
Use the following procedures to measure the Z dimensions:
Note: The left and right Z height differences should be no more than 10 mm (.39 in).
1. Push the front bumper down a minimum of 25 mm (1 in). Perform this step three times.
2. Measure and record the trim height per the "Measurement Definitions" above.
3. Lift the front bumper a minimum of 25 mm (1 in). Perform this step three times.
4. Measure and record the trim height per the "Measurement Definitions" above.
5. The true Z height dimension is the average of the measurements taken in steps 2 & 4. Refer to Trim Height Specifications Trim Height Specifications.
6. If these measurements are out of specifications, inspect for the following conditions:
* Worn or damaged suspension components
* Collision damage
D Height Measurement
Measurement Definitions
D Height GNE: The vertical distance between the center of the outer lower control arm bolt (1) to the center of the inner lower control arm bolt (2).
Use the following procedure to check the D dimension:
Note: The left and right D height difference should be no more than 10 mm (.39 in).
1. Push the rear bumper down a minimum of 25 mm (1 in). Perform this step three times.
2. Measure and record the trim height per the "Measurement Definitions" above.
3. Lift the rear bumper up a minimum of 25 mm (1 in), and release. Perform this step three times.
4. Measure and record the trim height per the "Measurement Definitions" above.
5. The true D height is the average of the measurements taken in steps 2 & 4. Refer to Trim Height Specifications Trim Height Specifications.
6. If these measurements are out of specifications, inspect for the following conditions:
* Worn or damaged suspension components
* Collision damage