Driver or Passenger Seat Side Inflatable Restraint Module Replacement

Driver or Passenger Seat Side Inflatable Restraint Module Replacement

Removal Procedures

Warning:
Refer to SIR Warning SIR Warning.


1. Disable the SIR system. Refer to SIR Disabling and Enabling Service and Repair.

2. Remove driver or passenger seat. Refer to Driver or Passenger Seat Replacement Driver or Passenger Seat Replacement.

3. Remove the driver or passenger seat outer recliner finish cover. Refer to Driver or Passenger Seat Outer Recliner Finish Cover Replacement Driver or Passenger Seat Outer Recliner Finish Cover Replacement.

4. Remove the driver or passenger seat inner recliner finish cover. Refer to Driver or Passenger Seat Inner Recliner Finish Cover Replacement Driver or Passenger Seat Inner Recliner Finish Cover Replacement.

5. Remove the driver or passenger seat head restraint. Refer to Driver or Passenger Seat Head Restraint Replacement Driver or Passenger Seat Head Restraint Replacement.





6. Clip out securing (1) of recliner control shaft (2), if equipped.





7. Remove recliner control (1) from recliner shaft (2), if equipped. Unhinge the cushion strap (3) at seat frame.





Note:
For loosening move the cushion upper and pull from backrest frame.

8. Loose the front seat back cushion at backrest left side (1) and right side (2).

9. Loose the front seat back cushion at backrest lower.

10. Remove hog rings at front seat back cushion to backrest wire.

11. Clip out the front seat back cushion vent fan mat (3) of vent fan (4), if equipped. Pull the cushion (5) in front to surface.





12. Loosen both nuts (1, 2) from seat side inflatable restraint module (3).





13. Disconnect the wiring harness connector (2) from seat side inflatable restraint module (1).





14. Disconnect wiring harness connector (1) of the seat back cushion heater, if equipped.





15. Remove front seat back cushion with cushion Pad (1) from backrest frame (2).





16. Remove seat side inflatable restraint module (1) out of the textile bag (2).

Installation Procedures





1. Install seat side inflatable restraint module (1) to textile bag (2).





2. Install front seat back cushion with cushion pad (1) at the backrest frame (2).





3. Connect the wiring harness connector (1) of the seat back cushion heater, if equipped.





Note:
Proof the correct locking of wiring harness connector (2).

4. Connect the wiring harness connector (2) from seat side inflatable restraint module (1).





Caution:
Refer to Fastener Caution Fastener Caution.

5. Position seat side inflatable restraint module (3) the backrest frame. Screw both nuts (1, 2) from seat side inflatable restraint module (3) and tighten to 3.25 Nm (29 lb in).





6. Clip in the front seat back cushion vent fan mat (3) at the vent fan (4), if equipped. Position the cushion (5).

7. Install new hog rings at front seat back cushion to backrest wire.

8. Install the front seat back cushion at backrest lower.

9. Install front seat back cushion at backrest left side (1) and right side (2).

10. Install the driver or passenger seat head restraint. Refer to Driver or Passenger Seat Head Restraint Replacement Driver or Passenger Seat Head Restraint Replacement.

11. Close the cushion at backrest rear side.

12. Install the driver or passenger seat inner recliner finish cover. Refer to Driver or Passenger Seat Inner Recliner Finish Cover Replacement Driver or Passenger Seat Inner Recliner Finish Cover Replacement.

13. Install the driver or passenger seat outer recliner finish cover. Refer to Driver or Passenger Seat Outer Recliner Finish Cover Replacement Driver or Passenger Seat Outer Recliner Finish Cover Replacement.

14. Install the driver or passenger seat. Refer to Driver or Passenger Seat Replacement Driver or Passenger Seat Replacement.