C0450
DTC C0450
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptors
DTC C0450 00
-
Steering Assist Control Actuator Circuit
DTC C0450 5A
-
Steering Assist Control Actuator Plausibility Failure
Diagnostic Fault Information
Circuit/System Description
The electronic brake control module (EBCM) controls the current through the Variable Effort Steering (VES) actuator located on the steering gear. The current used to control the VES actuator is between 0 and 1 Amp. At low speeds and in parking lot maneuvers the current is applied to the actuator causing the orifice to open increasing fluid flow and reducing the steering effort. At high speeds the orifice is commanded closed by reducing current through the actuator and restricting fluid flow increasing steering effort. The EBCM monitors and compares the Commanded and Feedback Current parameters to detect malfunctions in the VES system.
Conditions for Running the DTC
* The ignition is ON.
* Ignition voltage is greater than 8 volts.
Conditions for Setting the DTC
C0450 00
The actuator current exceeds 150mA.
C0450 5A
If the solenoid feedback voltage is greater than 80 percent while the actuator is commanded ON.
Action Taken When the DTC Sets
* The driver information center (DIC) will display SERVICE POWER STEERING message.
* Vehicle speed will be limited to 80 mph.
Conditions for Clearing the DTC
* The condition for setting the DTC is no longer present and the DTC is cleared with a scan tool.
* The EBCM automatically clears the history DTC when a current DTC is not detected in 100 consecutive drive cycles.
Diagnostic Aids
The vehicle may need to be driven to view full VES Actuator Commanded and Actuator Feedback Data parameters.
Reference Information
Schematic Reference
Power Steering Schematics Electrical Diagrams
Connector End View Reference
Component Connector End Views 5 Bow Lowered Switch (CM7)
Description and Operation
Variable Effort Steering System Description and Operation Variable Effort Steering System
Electrical Information Reference
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Circuit Testing Circuit Testing
Scan Tool Reference
Control Module References Control Module References for scan tool information
Circuit/System Testing
Important:
It is recommended that Component Testing is performed before Circuit/System Testing when diagnosing the VES actuator because the module will default and does not supply voltage to the sensor when the DTC is set.
1. Ignition OFF, disconnect the harness connector at the VES actuator.
Important:
In order to ensure correct test results, the J-35616 test lamp must be used to perform the following steps. Failure to use the J-35616 test lamp may result in inaccurate test results and potential misdiagnosis.
2. Ignition ON, verify that a test lamp illuminates between the control circuit terminal A and ground.
• If the test lamp does not illuminate, test the control circuit for a short to ground or an open/high resistance.
3. Ignition OFF, connect the test lamp between the control circuit terminal A and the control circuit terminal B.
4. Ignition ON, verify the test lamp briefly illuminates for approximately 1 second, then turns OFF.
• If the test lamp is always ON, test the control circuit terminal B for a short to ground. If the circuit tests normal, replace the EBCM.
• If the test lamp is always OFF, test the control circuit terminal B for a short to voltage or an open/high resistance. If the circuit tests normal, replace the EBCM.
5. If all circuits test normal, test or replace the VES actuator.
Component Testing
1. Ignition OFF, disconnect the VES actuator harness connector terminal A and B.
2. Measure for 2.5-10 ohms of resistance between the VES actuator terminals.
• If not 2.5-10 ohms of resistance, replace the VES actuator.
3. Measure for infinite ohms of resistance between each VES actuator terminals and the VES actuator housing.
• If less than the specified range, replace the VES actuator.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the diagnostic procedure.
* Control Module References Control Module References for EBCM replacement, setup, and programming.
* Steering Gear Replacement Service and Repair