Thermostat Housing: Service and Repair

Engine Coolant Thermostat Housing Replacement (LUW)

Removal Procedure

1. Remove the battery tray. Refer to Battery Tray Replacement Service and Repair.

2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle Service and Repair.

3. Drain the cooling system. Refer to Cooling System Draining and Filling Cooling System Draining and Filling.





4. Disconnect the engine harness connector (1) and harness fasteners (2) from the engine harness bracket, attached to the thermostat housing.





5. Disconnect the throttle body heater inlet hose (1) and the electrical connectors (2) from the thermostat housing.

6. Remove the engine harness bracket nut (3) and bracket (4) from the thermostat housing.





7. Remove the radiator inlet hose (2) from the engine coolant thermostat housing.

8. Remove the heater outlet hose from the engine coolant thermostat housing. Refer to Heater Outlet Hose Replacement (LUV) Heater Outlet Hose ReplacementHeater Outlet Hose Replacement (LDE, LUW) Heater Outlet Hose Replacement.

9. Remove the heater inlet hose from the engine coolant thermostat housing. Refer to Heater Inlet Hose Replacement (LDE, LUW) Heater Inlet Hose ReplacementHeater Inlet Hose Replacement (LUV) Heater Inlet Hose Replacement.





10. Remove the engine oil cooler outlet pipe bolts (1).

11. Remove the engine oil cooler outlet pipe (2) from the engine coolant thermostat housing.





12. Remove the engine coolant thermostat housing mounting bolts (1) and discard the seal (2).

13. Remove the engine coolant thermostat housing (3) from the engine.

Installation Procedure

1. Clean the sealing surface.





2. Install a NEW engine coolant thermostat housing seal (2).

3. Loosely install the engine coolant thermostat housing mounting bolts (1).





Caution:
Following the proper fastener tightening sequence and torque is essential. Failure to do so may fracture the thermostat housing.

Caution:
Refer to Fastener Caution Fastener Caution.

4. Tighten the 4 engine coolant thermostat housing bolts to 8 Nm (71 lb in) in sequence (1-2-3-4).





5. Install NEW engine oil cooler pipe seals (4, 7).

Note:
Push the engine oil cooler pipe into the engine oil cooler.

6. Install the engine oil cooler pipe (5).

7. Install the 2 engine oil cooler pipe bolts (6) and tighten to 8 Nm (71 lb in).

8. Install the heater inlet hose to the engine coolant thermostat housing. Refer to Heater Inlet Hose Replacement (LDE, LUW) Heater Inlet Hose ReplacementHeater Inlet Hose Replacement (LUV) Heater Inlet Hose Replacement.

9. Install the heater outlet hose to the engine coolant thermostat housing. Refer to Heater Outlet Hose Replacement (LUV) Heater Outlet Hose ReplacementHeater Outlet Hose Replacement (LDE, LUW) Heater Outlet Hose Replacement.





10. Connect the electrical connectors (2) to the engine coolant thermostat housing.

11. Install the throttle body heater inlet hose (1) to the engine coolant thermostat housing.

12. Install the engine coolant thermostat housing bracket (4) and nut (3) and tighten to 6 Nm (53 lb in).





13. Install the radiator inlet hose (2) to the engine coolant thermostat housing.

14. Fill the cooling system. Refer to Cooling System Draining and Filling Cooling System Draining and Filling.

15. Install the battery tray. Refer to Battery Tray Replacement Service and Repair.

16. Start the engine and check for coolant leaks.