Engine Cranks but Does Not Run
Engine Cranks But Does Not Run
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
Circuit/System Description
This Engine Cranks but Does Not Run diagnostic procedure is an organized approach to identify a condition which causes the engine to crank but not start. This diagnostic procedure directs the technician to the appropriate system diagnosis.
Diagnostic Aids
Inspect for any of the following conditions:
* When attempting to start the engine, the mechanical portion of the vehicle key must be locked in the fully extended position with the fob parallel to the key. Leaving the key partially retracted or folded over when starting may interrupt transponder authentication and result in an intermittent no-start condition. In such instances, DTC B3055 may also be set. If an intermittent no-start complaint is received, it may be necessary to discuss with the customer their starting habits and verify they are locking the key in the fully extended position, fob parallel to the key, before starting.
* The engine control module (ECM) uses the camshaft position sensors to determine engine speed and position when there is a crankshaft position sensor condition.
* The engine will operate with a crankshaft position sensor condition only if the ECM has stored the learned reference position of the camshafts in memory. With a crankshaft position sensor condition in the signal circuit, the engine will go into a limp home mode after a hard restart. The ECM then calculates engine speed from one of the camshaft position sensors.
* The fuel pump control module controls and monitors the operation of the in-tank fuel pump. If the fuel pump control module detects a fault, a DTC sets in the fuel pump control module. The fuel pump control module will then send a serial data message to the engine control module (ECM) requesting the illumination of the malfunction indicator lamp (MIL).
* Insufficient fuel can cause a no start condition. Thoroughly inspect the fuel delivery system for sufficient fuel volume to the fuel injectors. Inspect the fuel supply components for partial blockage or restrictions.
* Fuel injectors with partially blocked and restricted nozzles, or a malfunctioning solenoid, can cause a no start condition. Refer to Fuel Injector Solenoid Coil Test Fuel Injector Solenoid Coil Test.
* There may be fuel spray at the fuel injectors and the indicated fuel pressure may be correct, yet there may not be enough fuel to start the engine. If the fuel injectors and the injector circuit are OK, and fuel spray is detected, the fuel injector ON time may be inadequate. If the engine control module (ECM) receives incorrect inputs from the various information sensors, the fuel delivered by the fuel injectors may be inadequate to start the engine. Check all the engine data parameters with a scan tool and compare the values indicated with the expected values or the values from a known good vehicle.
* Inspect the engine for good secure electrical grounds.
* Water or foreign material in the fuel can cause a no start or engine will not stay running condition. During freezing weather water can freeze inside the fuel system. The engine may start after 30 min in a heated repair shop. The malfunction may not recur until parked overnight in freezing temperatures. Extreme weather conditions can cause contaminated fuel to prevent the vehicle from starting.
* A vehicle that starts and runs after being brought to the repair shop for a no start condition, may have an ignition system that is susceptible to moisture. Spray water on the ignition system components and the wiring in order to check for an engine starting or will not stay running concern.
Reference Information
Schematic Reference
Engine Controls Schematics (LAF) [1][2]Electrical Diagrams
Connector End View Reference
Component Connector End Views Sunshade - Left
Description and Operation
* Electronic Ignition System Description Description and Operation
* Fuel System Description Fuel System Description
* Immobilizer Description and Operation Immobilizer
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
Scan Tool Reference
Control Module References Programming and Relearning for scan tool information
Circuit/System Verification
Note: This diagnostic assumes the following:
* The battery is completely charged.
* There is adequate fuel in the tank.
1. Ignition ON, test the fuses that are supplied voltage by the K7 powertrain relay. The test lamp should illuminate for each test point of the fuses.
• If the test lamp does not illuminate for at least one test point of each fuse, refer to DTC P0685, P0689, P0690, or P1682 P0685 for powertrain relay system diagnosis.
2. Engine cranking, observe the Engine Speed parameter with a scan tool. The reading should show engine speed greater than 175 RPM.
• If the cranking speed is slow, refer to Engine Cranks Slowly Testing and Inspection.
• If engine speed reading is 0 RPM, refer to DTC P0335 or P0336 P0335 for crankshaft position sensor diagnosis.
3. Ignition ON, observe the ECM, fuel pump control module, and theft deterrent module DTC information with a scan tool. No DTCs should be set.
• If there are any DTCs set, refer to Diagnostic Trouble Code (DTC) List - Vehicle Diagnostic Trouble Code (DTC) List - Vehicle for diagnosis.
4. Disconnect the B75B mass airflow (MAF) sensor. Attempt to start the engine. The ECM will ignore MAF sensor input, default to calculated airflow, and the engine should start and run if the MAF sensor is faulted.
• If the engine starts and runs, and the MAF sensor circuits test OK, replace the B75B MAF sensor.
5. Ignition OFF, inspect the engine air filter, intake duct, and B75B MAF sensor. The air way should be clear.
• If the intake duct is blocked or collapsed, or the filter is restricted or water saturated, repair or replace as necessary.
• If the MAF sensor is damaged or contains water, replace it.
6. Ignition ON, observe the ECT Sensor parameter with a scan tool. Compare the parameter reading to the actual engine coolant temperature. The readings should be within ±3°C (±5°F).
• If the temperature readings are not within ±3°C (±5°F) of each other and the ECT sensor circuits test OK, replace the B34 ECT sensor.
7. Perform the Electronic Ignition System Diagnosis Electronic Ignition (EI) System Diagnosis to verify the ignition system provides spark to the cylinders.
8. Perform the Fuel System Diagnosis Fuel System Diagnosis to verify proper fuel pump operation and fuel pressure.
9. Verify that the following conditions do not exist:
* Gas or coolant fouled spark plugs
* A skewed engine coolant temperature (ECT) sensor-Refer to Temperature Versus Resistance Temperature Versus Resistance.
* Restricted exhaust system-Refer to Restricted Exhaust Restricted Exhaust.
* Contaminated fuel-Refer to Alcohol/Contaminants-in-Fuel Diagnosis Testing and Inspection and Fuel System Cleaning Service and Repair.
* An engine mechanical condition, for example, worn timing chain and gears or low compression-Refer to Symptoms - Engine Mechanical Symptoms - Engine Mechanical.
• If you find any of the above conditions, repair as necessary.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the diagnostic procedure.
* Air Cleaner Element Replacement Service and Repair
* Air Cleaner Outlet Duct Replacement Air Cleaner Outlet Duct Replacement
* Engine Coolant Temperature Sensor Replacement Service and Repair
* Mass Airflow Sensor with Intake Air Temperature Sensor Replacement Service and Repair
* Spark Plug Replacement Service and Repair