Air Bag Control Module: Service and Repair
Restraints Control Module (RCM)
NOTE: Vehicle with consolette tray shown.
Removal and Installation
WARNING: If a vehicle has been in a crash, inspect the restraints control module (RCM) and the impact sensor (if equipped) mounting areas for deformation. If damaged, restore the mounting areas to the original production configuration. A new RCM and sensors must be installed whether or not the air bags have deployed. Failure to follow these instructions may result in serious personal injury or death in a crash.
WARNING: Do not handle, move or change the original horizontal mounting position of the restraints control module (RCM) while the RCM is connected and the ignition switch is ON. Failure to follow this instruction may result in the accidental deployment of the Safety Canopy(R) and cause serious personal injury or death.
NOTICE: When installing a new Restraints Control Module (RCM), it is necessary to carry out Programmable Module Installation (PMI). System failure may occur if PMI is not performed. For additional information, refer to Information Bus. Programming and Relearning
NOTE: The air bag warning indicator illuminates when the correct RCM fuse is removed and the ignition is ON.
NOTE: The Supplemental Restraint System (SRS) must be fully operational and free of faults before releasing the vehicle to the customer.
1. When installing a new RCM, carry out the steps necessary for the Programmable Module Installation (PMI) procedure. For additional information, refer to Information Bus. Programming and Relearning
2. Depower the SRS. For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering in the General Procedures.
3. If equipped, remove the floor console. For additional information, refer to Instrument Cluster / Carrier &/or Interior Moulding / Trim.
4. If equipped, remove the consolette tray.
- Remove the consolette tray mat.
- Remove the 4 screws and consolette tray.
5. Disconnect the small RCM electrical connector.
6. Disconnect the large RCM electrical connector.
1. Pinch the thumb tab and pivot the connector position assurance lever all the way back until it stops.
2. Pull out and disconnect the RCM electrical connector.
7. Remove the 3 bolts and RCM.
Installation
1. WARNING: Always tighten the fasteners of the restraints control module (RCM) and impact sensor (if equipped) to the specified torque. Failure to do so may result in incorrect restraint system operation, which increases the risk of personal injury or death in a crash.
Install the RCM and 3 bolts.
- To install, tighten to 12 Nm (106 lb-in).
2. Make sure the large RCM connector position assurance lever is in the full release position before attempting to connect the connector.
3. NOTICE: Putting the large Restraints Control Module (RCM) electrical wiring connector into the RCM on an angle can cause bad electrical connections and damage components.
Position the large RCM electrical connector into the RCM.
- NOTICE: Do not push the connector to the point where the lever pivots and seats itself. Light pressure is needed to get the connector into position on the Restraints Control Module (RCM), before using the lever to fully seat the connector. Damage to the connector or component may occur.
With the large RCM electrical connector uniformly aligned to the RCM, lightly push in until a subtle audible click is heard and slight resistance is felt.
4. Connect the large RCM electrical connector.
- Using the connector position assurance lever, pivot it toward the RCM, drawing the connector into the RCM.
- Make sure the thumb tab is engaged to the retainer on the RCM and locked in place.
5. Connect the small RCM electrical connector.
6. If equipped, install the consolette tray.
- Install the consolette tray and 4 screws.
- Install the consolette tray mat.
7. If equipped, install the floor console. For additional information, refer to Instrument Cluster / Carrier &/or Interior Moulding / Trim.
8. Repower the SRS. Do not prove out the SRS at this time. For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering in the General Procedures.
9. If a new RCM was installed, carry out the appropriate steps in the Programmable Module Installation (PMI) procedure. For additional information, refer to Information Bus. Programming and Relearning
10. Prove out the SRS as follows:
Turn the ignition switch from ON to OFF. Wait 10 seconds, then turn the ignition switch back to ON and monitor the air bag warning indicator with the air bag modules installed. The air bag warning indicator will light continuously for approximately 6 seconds and then turn OFF. If an air bag SRS fault is present, the air bag indicator will:
- fail to light.
- remain lit continuously.
- flash at a 5 Hz rate (RCM not configured).
The air bag warning indicator might not light until approximately 30 seconds after the ignition switch has been turned from the OFF to the ON position. This is the time required for the RCM to complete the testing of the SRS. If the air bag indicator is inoperative and a SRS fault exists, a chime will sound in a pattern of 5 sets of 5 beeps. If this occurs, the air bag indicator and any SRS fault discovered must be diagnosed and repaired.
Clear all continuous DTCs from the RCM and Occupant Classification System Module (OCSM) using a scan tool.