Fuel Rail Assembly Replacement
REMOVAL PROCEDUREIMPORTANT: An eight-digit identification number (1) is located on the fuel rail assembly. Refer to this model identification number if servicing or part replacement is required.
1. Remove the engine sight shield.
2. Before removal, clean the fuel rail assembly with a spray type engine cleaner, GM X - 30A or equivalent, if necessary. Follow the package instructions. Do not soak fuel rails in liquid cleaning solvent.
3. Disconnect the accelerator control cable and the cruise control cable from the cable bracket.
4. Disconnect the accelerator control cable and the cruise control cable from the throttle body.
5. Remove the upper engine wire harness retainer nut.
6. Disconnect the evaporative emission (EVAP) purge valve harness connector.
7. Reposition the upper engine wire harness aside.
8. Relieve the fuel system pressure. Refer to Fuel Pressure Relief Procedure.
9. Identify the connectors to their corresponding injectors to ensure correct sequential injector firing order after reassembly.
10. Pull the top portion (2) of the injector connector up. Do not pull the top portion of the connector past the top of the white portion (1).
11. Push the tab (1) on the lower side of the injector connector in order to release the connector from the injector.
12. Repeat Step 12 and Step 13 for each injector connector.
NOTE: Refer to Removing Fuel Rail Assembly Notice in Service Precautions.
13. Disconnect the fuel feed and return pipes (1,2) from the fuel rail.
14. Disconnect the fuel pressure regulator vacuum line.
15. Loosen the crossover tube to right fuel rail retainer screw (22).
16. Remove the fuel rail attaching bolts.
17. Remove the fuel rail assembly.
18. Remove the injector lower O-ring seal (4) from the spray tip end of each injector (3).
19. Discard the O-ring seals.
INSTALLATION PROCEDURE
1. Lubricate the new lower injector O-ring seals (4) with clean engine oil.
2. Install the new O-ring seals (4) on the spray tip end of each injector (3).
3. Remove the crossover tube to the right fuel rail retainer (21).
4. Remove the crossover tube (25) from the right fuel rail (15).
5. Remove the O-ring (20) from the crossover tube (25).
6. Install a new O-ring on the crossover tube.
7. Lubricate the new O-ring with clean engine oil.
8. Install the crossover tube (25) into the right fuel rail (15).
9. Loosely install the crossover tube to the right fuel rail retainer (21).
10. Install the fuel rail assembly to the intake manifold.
11. Apply a 5 mm (0.020 in) band of GM P/N 12345382 thread lock, or equivalent, to the threads of the fuel rail bolts.
NOTE: Refer to the Fastener Notice in Service Precautions.
12. Install the fuel rail attaching bolts.
Tighten
12.1. Tighten the bolts to 10 N.m (89 lb in).
12.2. Tighten the right crossover pipe retainer screw to 3.8 N.m (34 lb in).
13. Connect the fuel pressure regulator vacuum line.
14. Connect the fuel feed and return pipes (1, 2) to the fuel rail.
15. Connect the injector electrical connectors.
^ Install each connector on the proper injector in order to ensure correct sequential injector firing order.
^ Rotate the injectors as required in order to avoid stretching the wire harness.
16. Position the upper engine wire harness in place.
17. Connect the EVAP purge solenoid connector.
18. Install the retainer nut to the upper engine wire harness.
Tighten
Tighten the nut to 5.5 N.m (49 lb in).
19. Connect the accelerator control cable and the cruise control cable to the cable bracket.
20. Connect the accelerator control cable and the cruise control cable to the throttle body.
21. Install the engine sight shield mounting bracket and the bolts.
22. Tighten the fuel tiller cap.
23. Connect the negative battery cable.
24. Use the following procedure in order to inspect for leaks:
24.1. Turn ON the ignition, with the engine OFF, for 2 seconds.
24.2. Turn OFF the ignition for 10 seconds.
24.3. Turn ON the ignition, with the engine OFF.
24.4. Inspect for fuel leaks.
25. Install the engine sight shield.