P1705
DTC P1705 THROTTLE POSITION SENSORDescription
Electric throttle control actuator consists of throttle control motor, accelerator pedal position sensor, throttle position sensor, etc. The actuator sends a signal to the ECM, and ECM sends signals to TCM with CAN communication.
CONSULT-II Reference Value:
On Board Diagnosis Logic
^ This is not an OBD-II self-diagnostic item.
^ Diagnostic trouble code "P1705 TP SEN/CIRC A/T" with CONSULT-II or 15th judgement flicker without CONSULT-II is detected when TCM does not receive the proper accelerator pedal position signals (input by CAN communication) from ECM.
Possible Cause
Harness or connectors
(Sensor circuit is open or shorted.)
DTC Confirmation Procedure
NOTE: If "DTC Confirmation Procedure" has been previously performed, always turn ignition switch OFF and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
With CONSULT-II
1. Turn ignition switch ON.
2. Select "ECU INPUT SIGNALS" in "DATA MONITOR" mode for "A/T" with CONSULT-II.
3. Touch "START".
4. Start engine and let it idle for 1 second.
5. If DTC is detected, go to AT-132, "Diagnostic Procedure".
Diagnostic Procedure
1. CHECK CAN COMMUNICATION LINE
Perform the self-diagnosis. Refer to AT-92, "SELF-DIAGNOSTIC RESULT MODE", AT-102, "Diagnostic Procedure without CONSULT-II".
Self-Diagnostic Result Mode
Is a malfunction in the CAN communication indicated in the results?
YES >> Check CAN communication line. Refer to AT-104, "DTC U1000 CAN COMMUNICATION LINE". U1000
NO >> GO TO 2.
2. CHECK DTC WITH TCM
With CONSULT-II
1. Turn ignition switch ON.
2. Select "ECU INPUT SIGNALS" in "DATA MONITOR" mode for "A/T" with CONSULT-II.
3. Depress accelerator pedal and read out the value of "ACCELE POSI".
4. Select "SELF-DIAG RESULTS" mode for "A/T" with CONSULT-II. Refer to AT-92, "SELF-DIAGNOSTIC RESULT MODE". Self-Diagnostic Result Mode
OK or NG
OK >> GO TO 4.
NG >> GO TO 3.
3. CHECK DTC WITH ECM
With CONSULT-II
1. Turn ignition switch ON.
2. Select "SELF-DIAG RESULTS" mode for "ENGINE" with CONSULT-II. Refer to EC-118, "CONSULT-II Function (ENGINE)" (for VQ35DE) or EC-781, "CONSULT-II Function (ENGINE)" (for VK45DE).
CONSULT-II Function (ENGINE)
CONSULT-II Function (ENGINE)
OK or NG
OK >> GO TO 4.
NG >> Check the DTC detected item. Refer to EC-118, "CONSULT-II Function (ENGINE)" (for VQ35DE) or EC-781, "CONSULT-II Function (ENGINE)" (for VK45DE).
CONSULT-II Function (ENGINE)
CONSULT-II Function (ENGINE)
^ If CAN communication line is detected, go to AT-104, "DTC U1000 CAN COMMUNICATION LINE". U1000
4. CHECK DTC
Perform AT-131, "DTC Confirmation Procedure".
OK or NG
OK >> INSPECTION END
NG >> GO TO 5.
5. CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to AT-179, "MAIN POWER SUPPLY AND GROUND CIRCUIT".
OK or NG
OK >> GO TO 6.
NG >> Repair or replace damaged parts.
6. DETECT MALFUNCTIONING ITEM
Check A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG
OK >> Replace the control valve with TCM.
NG >> Repair or replace damaged parts.