P0451
P0451 EVAP CONTROL SYSTEM PRESSURE SENSOR
Description
The EVAP control system pressure sensor detects pressure in the purge line. The sensor output voltage to the ECM increases as pressure increases.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1. PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
1.Turn ignition switch OFF and wait at least 10 seconds.
2.Turn ignition switch ON.
3.Turn ignition switch OFF and wait at least 10 seconds.
With CONSULT-GO TO 2.
Without CONSULT-GO TO 5.
2. PERFORM DTC CONFIRMATION PROCEDURE-1
With CONSULT
1.Start engine and wait at least 40 seconds.
NOTE:
Do not depress accelerator pedal even slightly.
2.Check 1st trip DTC.
Is 1st trip DTC detected?
YES- Proceed to .
NO- GO TO 3.
3. PERFORM DTC CONFIRMATION PROCEDURE-2
With CONSULT
1.Select "EVAP DIAG READY" in "DATA MONITOR" mode of "ENGINE".
2.Let it idle until "OFF" of "EVAP DIAG READY" changes to "ON".
NOTE:
It will take at most 2 hours until "OFF" of "EVAP DIAG READY" changes to "ON".
3.Turn ignition switch OFF and wait at least 90 minutes.
NOTE:
Never turn ignition switch ON during 90 minutes.
4.Turn ignition switch ON.
5.Select "EVAP LEAK DIAG" in "DATA MONITOR" mode of "ENGINE".
6.Check that "EVAP LEAK DIAG" indication.
Which is displayed on CONSULT?
"CMPLT"-GO TO 4.
"YET"- 1.Perform DTC CONFIRMATION PROCEDURE again.
2.GO TO 1.
4. PERFORM DTC CONFIRMATION PROCEDURE-3
With CONSULT
Check 1st trip DTC.
Is 1st trip DTC detected?
YES- Proceed to .
NO- INSPECTION END.
5. PERFORM DTC CONFIRMATION PROCEDURE-4
Without CONSULT
1.Start engine and wait at least 40 seconds.
NOTE:
Do not depress accelerator pedal even slightly.
2.Check 1st trip DTC.
Is 1st trip DTC detected?
YES- Proceed to .
NO- GO TO 6.
6. PERFORM DTC CONFIRMATION PROCEDURE-5
Without CONSULT
1.Let it idle for at least 2 hours.
2.Turn ignition switch OFF and wait at least 90 minutes.
NOTE:
Never turn ignition switch ON during 90 minutes.
3.Turn ignition switch ON.
4.Check 1st trip DTC.
Is 1st trip DTC detected?
YES- Proceed to .
NO- INSPECTION END.
Diagnosis Procedure
1. CHECK GROUND CONNECTION
1.Turn ignition switch OFF.
2.Check ground connection M95. Refer to Ground Inspection in Circuit Inspection.
Is the inspection result normal?
YES- GO TO 2.
NO- Repair or replace ground connection.
2. CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR CONNECTOR FOR WATER
1.Disconnect EVAP control system pressure sensor harness connector.
2.Check sensor harness connector for water.
Water should not exist.
Is the inspection result normal?
YES- GO TO 3.
NO- Repair or replace harness connector.
3. CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR POWER SUPPLY CIRCUIT
1.Turn ignition switch ON.
2.Check the voltage between EVAP control system pressure sensor harness connector and ground.
Is the inspection result normal?
YES- GO TO 8.
NO- GO TO 4.
4. CHECK SENSOR POWER SUPPLY CIRCUIT
Check harness for short to power and short to ground, between the following terminals.
Is the inspection result normal?
YES- GO TO 5.
NO- Repair short to ground or short to power in harness or connectors.
5. CHECK COMPONENTS
Check the following.
- CKP sensor (P0335.)
- CMP sensor (bank 2) (P0340.)
- EVT control position sensor (bank 2) (P1078.)
- Battery current sensor (P1550.)
- Refrigerant pressure sensor (Magnetic Clutch.)
Is the inspection result normal?
YES- GO TO 6.
NO- Replace malfunctioning component.
6. CHECK APP SENSOR
P2122.
Is the inspection result normal?
YES- GO TO 9.
NO- GO TO 7.
7. REPLACE ACCELERATOR PEDAL ASSEMBLY
Replace accelerator pedal assembly. Without Distance Control Assist System (without distance control assist) or {LINK_TO_MANY:0000000007512473}{LINK_TO_MANY:0000000007512474}, "MODELS WITH DISTANCE
CONTROL ASSIST SYSTEM : Removal and Installation" (without distance control assist).
- INSPECTION END
8. CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
.
Is the inspection result normal?
YES- GO TO 9.
NO- Replace EVAP control system pressure sensor. Removal and Installation.
9. CHECK INTERMITTENT INCIDENT
Perform Intermittent Incident.
- INSPECTION END
Component Inspection
1. CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
1.Turn ignition switch OFF.
2.Remove EVAP control system pressure sensor with its harness connector. Removal and Installation.
Always replace O-ring with a new one.
3.Install a vacuum pump to EVAP control system pressure sensor.
4.Turn ignition switch ON and check output voltage between ECM harness connector terminals as per the following conditions.
CAUTION:
- Always calibrate the vacuum pump gauge when using it.
22
- Never apply below -93.3 kPa (-0.952 kg/cm, -13.53 psi) or pressure over 101.3 kPa (1.033 kg/cm, 14.69 psi).
Is the inspection result normal?
YES- INSPECTION END
NO- Replace EVAP control system pressure sensor. Removal and Installation.