Operation CHARM: Car repair manuals for everyone.

P1701




P1701 TCM

Description

When the power supply to the TCM is cut off, for example because the battery is removed, and the self-diagnosis memory function stops, a malfunction is detected.
Detects malfunction when power source (backup) is not supplied to TCM and learning function is stopped.

CAUTION:
"P1701" can be displayed in self diagnosis result immediately after TCM replacement and after transaxle assembly replacement (after TCM initialization operation). In this case, erase self diagnosis result using CONSULT. After erasing self diagnosis result, perform reproducing operation of "P1701"
to confirm that there is no longer malfunction.


DTC Logic


DTC DETECTION LOGIC







DTC CONFIRMATION PROCEDURE


CAUTION:
Always drive vehicle at a safe speed.

1. PRECONDITIONING

If "DTC CONFIRMATION PROCEDURE" has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.
- GO TO 2.

2. CHECK DTC DETECTION

With CONSULT
1.Start the engine.
2.Maintain the idling conditions for 10 seconds or more.
3.Drive the vehicle for 10 seconds or more.
4.Stop the vehicle.
5.Turn ignition switch OFF.
6.Wait for 10 seconds or more.
7.Start the engine.
8.Check DTC.
Is "P1701" detected?
YES- Go to "Diagnosis Procedure" .
NO- INSPECTION END


Diagnosis Procedure

Regarding Wiring Diagram information, refer to "Wiring Diagram" Electrical Diagrams.

1. CHECK TCM POWER SOURCE (PART 1)

1.Turn ignition switch OFF.
2.Disconnect TCM connector.
3.Check voltage between TCM harness connector terminals and ground.
Revision: March 20122013 Infiniti JX





Is the inspection result normal?
YES- GO TO 2.
NO- GO TO 3.

2. CHECK TCM POWER SOURCE (PART 2)

1.Turn ignition switch OFF.
2.Check voltage between TCM harness connector terminals and ground.





Is the inspection result normal?
YES- GO TO 7.
NO- GO TO 5.

3. CHECK CIRCUIT BETWEEN TCM AND IPDM E/R

1.Turn ignition switch OFF.
2.Disconnect IPDM E/R connector.
3.Check continuity between IPDM E/R harness connector terminals and TCM harness connector terminal.





4.Check continuity between IPDM E/R harness connector terminals and ground.





Is the inspection result normal?
YES- GO TO 4.
NO- Repair or replace damaged parts.

4. DETECT MALFUNCTIONING ITEMS

Check the following items.
- IPDM E/R
- 10A fuse (# 46, located in IPDM E/R)
- Harness for short or open between IPDM E/R and ignition switch
- Ignition switch
Is the inspection result normal?
YES- Check intermittent incident. Refer to "Intermittent Incident" Intermittent Incident.
NO- Repair or replace damaged parts.
Revision: March 20122013 Infiniti JX

5. CHECK CIRCUIT BETWEEN TCM AND FUSE BLOCK (J/B)

1.Turn ignition switch OFF.
2.Disconnect fuse block (J/B) connector.
3.Check continuity between fuse block (J/B) harness connector terminals and TCM harness connector terminal.





4.Check continuity between fuse block (J/B) harness connector terminals and ground.





Is the inspection result normal?
YES- GO TO 6.
NO- Repair or replace damaged parts.

6. DETECT MALFUNCTIONING ITEMS

Check the following items.
- Harness for short or open between battery and fuse block (J/B)
- 10A fuse [# 25, located in Fuse block (J/B)]
- Fuse block (J/B)
- Battery
Is the inspection result normal?
YES- Check intermittent incident. Refer to "Intermittent Incident" Intermittent Incident.
NO- Repair or replace damaged parts.

7. CHECK GROUND CIRCUIT

Check continuity between TCM harness connector terminals and ground.





Is the inspection result normal?
YES- Check intermittent incident. Refer to "Intermittent Incident" Intermittent Incident.
NO- Repair or replace damaged parts.
Revision: March 20122013 Infiniti JX