Removal and Installation

INSTRUMENT PANEL ASSEMBLY

Removal and Installation


WORK STEP

When removing instrument panel assembly, combination meter, front display unit, AV control unit, instrument finisher A, instrument finisher B, and center console assembly take steps as per the order shown in the following chart.











WARNING:
Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes or more.

CAUTION:
When removing, always use a remover tool that is made of plastic.

REMOVAL






1.Remove instrument lower cover.
1.Pull disengaged pawls downward.
2.Pull back instrument lower cover.
3.Disconnect harness connectors.










2.Remove glove box assembly.
1.Remove glove box assembly fixing screws (A).
2.Open glove box lid.
3.Remove glove box assembly fixing screws (B).
4.Pull back glove box assembly.
5.Disconnect harness connector.










3.Disconnect harness connector (A) of front passenger air bag module.
4.Remove front passenger air bag module mounting bolt (B).
5.Remove selector lever knob. Refer to "Removal and Installation" Removal and Installation.





6.Remove console finisher assembly.
1.Put front seat to rearmost position.
2.Pull console finisher assembly upward to disengage from center console assembly.
3.Disconnect harness connectors.





7.Remove instrument center finisher RH.





1.Pull the instrument center finisher RH lower side, and then disengage the fixing clip.





2.Pull back instrument center finisher RH, and then disengage metal clips.
3.Disengage instrument center finisher RH fixing pawl from instrument panel assembly.










8.Remove front body side welt RH. Refer to "BODY SIDE WELT : Removal and Installation" Body Side Welt.
9.Remove front pillar garnish RH. Refer to "FRONT PILLAR GARNISH : Removal and Installation" Front Pillar Garnish.
10.Remove speaker grille RH.





1.Disengage speaker grille RH fixing pawls with remover tool (A).
2.Pull up speaker grille RH.

CAUTION:
Apply protective tape (B) on the part to protect it from damage.





11.Remove squawker RH. Refer to "Removal and Installation" Squawker.
12.Remove front defroster grille RH. Refer to "FRONT DEFROSTER GRILLE : Removal and Installation" Front Defroster Grille.
13.Remove front defroster grille LH. Refer to "FRONT DEFROSTER GRILLE : Removal and Installation" Front Defroster Grille.
14.Remove instrument center finisher LH.





1.Pull the instrument center finisher LH lower side, and then disengage the fixing clip.





2.Pull back instrument center finisher LH, and then disengage metal clips.
3.Disengage instrument center finisher LH fixing pawl from instrument panel assembly.










15.Remove console rear finisher.





1.Put front seat to frontmost position.
2.Pull back console rear finisher with remover tool (A).
3.Disconnect harness connectors and harness clips.

CAUTION:
Apply protective tape (B) on the part to protect it from damage.





16.Remove center console assembly.





1.Remove centre console assembly rear side fixing screws (A).
2.Put front seat to rearmost position.





3.Remove center console assembly front fixing screws (B).
4.Lift up center console assembly back side, and then remove center console assembly.
17.Remove front body side welt LH. Refer to "BODY SIDE WELT : Removal and Installation" Body Side Welt.
18.Remove front pillar garnish LH. Refer to "FRONT PILLAR GARNISH : Removal and Installation" Front Pillar Garnish.





19.Remove speaker grille LH.
1.Disengage speaker grille LH fixing pawls with remover tool (A).
2.Pull up speaker grille LH.

CAUTION:
Apply protective tape (B) on the part to protect it from damage.





20.Remove squawker LH. Refer to "Removal and Installation" Squawker.
21.Remove instrument lower panel LH.
1.Remove food opener lever fixing bolts. Refer to "Removal and Installation" Removal and Installation





2.Pull back instrument lower panel LH, and then disengage the clips and pawl.
3.Disconnect harness connectors and aspirator duct.










22.Disconnect meter control switch harness connector (A).
23.Remove driver air bag module. Refer to "Removal and Installation" Removal and Installation.
24.Remove steering wheel. Refer to "Removal and Installation" Removal and Installation.





25.Remove steering column covers.
1.Remove steering column cover fixing screws (A).
2.Pull up steering column upper cover (1), and then disengage steering column upper cove fixing pawls.
3.Remove steering column upper cover.
4.Pull down steering column lower cover (2), and then disconnect ADP steering switch connector (with ADP).
5.Remove steering column lower cover.





26.Remove combination switch. Refer to "Removal and Installation" Removal and Installation.
27.Remove spiral cable. Refer to "Removal and Installation" Removal and Installation.





28.Remove cluster lid A.
1.Pull back cluster lid A, and then disengage the clips and pawls.
2.Disconnect harness connectors.





29.Remove combination meter. Refer to "Removal and Installation" Removal and Installation.





30.Remove upper ventilator grille.
1.Disengage upper ventilator grille fixing clips and pawls with remover tool (A)
2.Pull toward the arrow direction.

CAUTION:
Apply protective tape (B) on the part to protect it from damage.





31.Remove center speaker. Refer to "Removal and Installation" Center Speaker.





32.Remove cluster lid C.
1.Remove cluster lid C fixing screws (A).
2.Pull back cluster lid C, and then disengage the pawls and metal clips.
3.Disconnect harness connectors.










33.Remove cluster lid C lower.
1.Disengage cluster lid C lower fixing metal clips with remover tool (A).
2.Pull back cluster lid C lower, and then disconnect harness connectors.

CAUTION:
Apply protective tape (B) on the part to protect it from damage.





NOTE:
When removing cluster lid C lower without removing center console.





1.Disengage metal clips of lower side of cluster lid C lower using a remover tool (A).
2.Disengage metal clips of upper side of cluster lid C lower using a remover tool.
3.Pull back cluster lid C lower, and then disconnect harness connectors.





34.Remove AV control unit. Refer to "Removal and Installation" Service and Repair.
35.Remove cluster lid D.





1.Remove cluster lid D fixing screw (A).
2.Pull back cluster lid D, and then disengage the pawls and metal clips.





36.Remove front display unit. Refer to "Removal and Installation" Service and Repair.
37.Remove instrument panel assembly mounting screws (A) and bolts (B).





38.Pull back instrument panel assembly, and then remove front squawker LH harness (1) fixing clip (A) from front ventilator duct (2).





39.Remove instrument panel from passenger door opening portion.

CAUTION:
- Cover tool with a shop cloth to prevent windshield glass from being damaged.
- When removing instrument panel assembly, 2 workers are required so as to prevent it from dropping.
40.Remove the following parts after removing instrument panel assembly.
- Front passenger air bag module. Refer to "Removal and Installation" Removal and Installation.
- Side ventilator grille LH/RH. Refer to "SIDE VENTILATOR GRILLE : Removal and Installation" Side Ventilator Grille.
- Side ventilator duct: Refer to "SIDE VENTILATOR DUCT : Removal and Installation" Side Ventilator Duct.
- Upper ventilator duct: Refer to "UPPER VENTILATOR DUCT : Removal and Installation" Upper Ventilator Duct.
- Front defroster nozzle: Refer to "FRONT DEFROSTER NOZZLE : Removal and Installation" Front Defroster Nozzle.
- Side defroster nozzle: Refer to "SIDE DEFROSTER NOZZLE : Removal and Installation" Side Defroster Nozzle.
- GPS antenna: Refer to "Removal and Installation" Service and Repair.
- Instrument finisher A
- Instrument finisher B

INSTALLATION

Install in the reverse order of removal.