Pre-Check

PRE-CHECK




1. DIAGNOSIS SYSTEM MODE

HINT: Diagnosis System is operated as shown.

a. Diagnosis Start-Up

HINT:
- Before starting the Diagnosis System, make sure that the map appears on the screen after turning on the IG switch. If not, some items cannot be checked.
- To start the diagnosis menu, there are 2 ways: using a light control switch and using a touch switch.







b. Diagnosis Start-up by light control switch.

1. Vehicle speed should be 0 km/h (0 mph).
2. Turn the ignition switch to ACC or ON.
3. While pressing the "INFO" switches on the Multi Display, turn the Light Control switch from OFF->TAIL->OFF->TAIL->OFF->TAIL->OFF.

HINT:
- When Diagnosis System starts, Service Check screen is displayed and the service check begins.
- Select MENU to display Diagnosis Check Menu.




c. Diagnosis Start-Up by touch switch.

1. Vehicle speed should be 0 km/h (0 mph).
2. Turn the ignition switch to ACC or ON.
3. Activate the screen adjustment screen.
4. Alternately touch the upper and lower bottom parts of the left end of the screen 3 times.

d. Finishing the Diagnosis System
Turn the ignition switch off to finish the mode.




2. SERVICE CHECK MODE

HINT: Service Check Mode is operated as shown.

a. Service Check Screen

b. Service Check







1. Start the Diagnosis System

HINT: Service Check displays the check results based on the information obtained from each component's response to "System Check Execution" and "Diagnosis Memory Request", and the information of "Current DTC Notification" (the Unit Check and the LAN Check information that will be displayed on the next screens.).




2. Read Check Result.

HINT:
- After repair and check, press "Code CLR" for more than 3 sec. to delete diagnosis memory.
- After deleting diagnosis memory, press "Recheck" and make sure "OK" is displayed on the screen.







3. "EXCH", "CHEK" and "Old" can be used as switches to activate "Unit Check Mode" for detail information. Check troubled parts of the components in these modes by referring to the DTC code list.

HINT:
- Detecting Unit DTC activates the Unit Check Mode on the screen.
- In the Unit Check Mode, DTC identified as "EXCH" in the Service Check is displayed as classified into Current DTC and Past DTC.

c. LAN Monitor







1. Start the Diagnosis System.

HINT: System Check displays the check results based on the information obtained from each component's response to "System Check Execution" and "Diagnosis Memory Request", and the information of "Current DTC Notification" (the LAN Monitor that will be displayed on the next screens).




2. Read Check Result

HINT:
- After repair and check, press "Code CLR" for more than 3 sec. to delete diagnosis memory.
- After deleting diagnosis memory, press "Recheck" and make sure that "OK" is displayed on the screen.







3. "CHEK" can be used as switches to activate "LAN Monitor" for detail information. Check troubled parts of the components in these modes by referring to the DTC code list.

HINT: Detecting no LAN DTC activates the LAN Check Mode on the screen.




3. NAVIGATION CHECK MODE

HINT: Navigation Check Mode is operated as shown.











a. Navigation Check Mode Screen

HINT:
- In the Navigation Check mode the checks mentioned above can be conducted.
- The Navigation ECU operates each Navigation Check screen













b. GPS Information

1. Start the Diagnosis system
2. Select "MENU"
3. Select Navigation Check"
4. Select "GPS Information".
5. Check the GPS-related information.







c. Vehicle Signal Check

1. Start the Diagnosis system.
2. Select "MENU".
3. Select "Navigation Check".
4. Select "Vehicle sensors".
5. Check the vehicle signals (ACC, REV, SPD) and the output signal of the gyro sensor introduced into the navigation ECU.







d. Navigation Color Bar Check

1. Start the Diagnosis system.
2. Select "MENU".
3. Select "Navigation Check".
4. Select "Color Bar Check".
5. Make sure that the set color matches the display color.
6. Compare with the Color Bar Check in the Display Check and make sure that no difference is found.







e. Parts Information

1. Start the Diagnosis system.
2. Select "MENU".
3. Select "Navigation Check".
4. Select "Parts Information".
5. Check the program and disc version.







f. Memory Copy/Paste

HINT: This function is not available.




4. DISPLAY CHECK MODE










a. Display Check Mode

HINT: In Display Check Mode, above checks can be performed




b. Display Color Bar Check

1. Start the Diagnosis System
2. Select "MENU".
3. Select "Display Check"
4. Select "Color Bar Check"
5. Make sure that each color name is corresponding to each color on the bar.

HINT: Select Black, Red, Green, Blue, White and Stripe to display selected colors and stripe on the entire screen




6. Compare with the Color Bar Check in the Navigation Check and make sure that no difference is found.







c. Display Touch Switch Check

1. Start the Diagnosis system.
2. Select "MENU".
3. Select "Display Check".
4. Select "Touch Switch Check".
5. Touch the screen and make sure that every line reacts to the touch.

HINT: After the Touch Switch Check for vertical lines, press "Next" to check horizontal lines.







d. Display Touch Point Check

1. Start the Diagnosis system.
2. Select "MENU".
3. Select "Display Check".
4. Select "Touch Point Check".
5. The position detected by the pressure sensing touch switch is checked.







e. Display Panel Switch Check

1. Start the Diagnosis system.
2. Select "MENU".
3. Select "Display Check".
4. Select "Panel Switch Check".
5. Press each switch and make sure that they correspond to the display on the screen.







f. Display Vehicle Signal Check

1. Start the Diagnosis system.
2. Select "MENU".
3. Select "Display Check".
4. Select "Vehicle Signal Check"
5. Check the status of the vehicle signal (Battery, PKB, SPEED, TAIL, ADIM/TCAN) loaded into the display.

HINT: Vehicle signal data is updated every 1 second.