Operation Check

NAVIGATION / MULTI INFO DISPLAY: NAVIGATION SYSTEM: OPERATION CHECK

1. CHECK SYSTEM NORMAL CONDITION

(a) If the cause of a symptom is any of the following, the corresponding symptom is normal; it is not a malfunction.





(b) The following symptoms are not malfunctions, but are caused by errors inherent in the GPS, gyro sensor, speed sensor or display and navigation module display.





(1) The current position mark may be displayed on a nearby parallel road.

(2) Immediately after a fork in the road, the current vehicle position mark may be displayed on the wrong road.





(3) When the vehicle turns right or left at an intersection, the current vehicle position mark may be displayed on a nearby parallel road.





(4) When the vehicle is carried, such as on a ferry, and the vehicle itself is not being driven, the current vehicle position mark may be displayed in the position where the vehicle was until a measurement can be performed using GPS.





(5) When the vehicle travels on a steep hill, the current vehicle position mark may deviate from the correct position.





(6) When the vehicle makes a continuous turn (e.g. 360, 720 or 1080 degrees), the current vehicle position mark may deviate from the correct position.





(7) When the vehicle moves erratically, such as when making constant lane changes, the current vehicle position mark may deviate from the correct position.





(8) When the engine switch is turned on (ACC) or on (IG) on a turntable before parking, the current vehicle position mark may not indicate the correct direction. The same will occur when the vehicle comes out of the parking garage.





(9) When the vehicle travels on a snowy road or a mountain path with tire chains installed or using a spare tire, the current vehicle position mark may deviate from the correct position.





(10) When the tires are changed, the current vehicle position mark may deviate from the correct position.





HINT
* A change in tire diameter may cause a speed sensor error.
* Performing "tire change" in calibration mode will allow the system to correct the current vehicle position faster.

2. CHECK HARD DISK DRIVE

HINT
* Check the hard disk drive (HDD) built into the display and navigation module display.
* Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be exactly the same as on the actual vehicle screen.

(a) Enter diagnostic mode Reading and Clearing Diagnostic Trouble Codes.

(b) Select "Failure Diagnosis" from the "Service Menu" screen.





(c) Hard disk drive check





(1) Select "HDD Check" to start the HDD check.

(2) Check that the result is displayed when the HDD check is completed.

Screen Description





HINT
* After selecting "HDD Check", it may take a while until the result is displayed.
* Replace the display and navigation module display when NG is displayed.

3. CHECK PANEL & STEERING SWITCH

HINT
* The display and navigation module display panel switches, radio receiver assembly panel switches and steering pad switches are checked in the following procedure.
* Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be exactly the same as on the actual vehicle screen.

(a) Enter diagnostic mode Reading and Clearing Diagnostic Trouble Codes.

(b) Select "Function Check/Setting" from the "Service Menu" screen.





(c) Select "Panel & Steering Switch" from the "Function Check/Setting" screen.





(d) Panel & Steering Switch Check Mode

(1) Operate each switch and check that the switch names and conditions are correctly displayed.





Screen Description





4. CHECK TOUCH SWITCH

HINT
* The touch switches on the screen are checked in the following procedure.
* Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be exactly the same as on the actual vehicle screen.

(a) Enter diagnostic mode Reading and Clearing Diagnostic Trouble Codes.

(b) Select "Function Check/Setting" from the "Service Menu" screen.





(c) Select "Touch Switch" from the "Function Check/Setting" screen.





(d) Touch Switch Check





(1) Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

HINT
* A "+" mark is displayed where the display is touched.
* The "+" mark remains on the display even after the finger is removed.

5. CHECK MIC & VOICE RECOGNITION

HINT
* The microphone and microphone input level are checked in the following procedure.
* Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be exactly the same as on the actual vehicle screen.

(a) Enter diagnostic mode Reading and Clearing Diagnostic Trouble Codes.

(b) Select "Function Check/Setting" from the "Service Menu" screen.





(c) Select "Mic & Voice Recognition" from the "Function Check/Setting" screen.





(d) Microphone & Voice Recognition Check

(1) When speaking into the microphone, check that the microphone input level meter changes according to the input level.





(2) Push the recording switch and perform voice recording.

HINT
* Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.
* Voice can be recorded for up to 5 seconds.

(3) Check that the recording indicator remains on while recording and that the recording can be played normally.

Text in Illustration





HINT
* For details of this function, refer to Diagnosis Display Detailed Description System Description.
* This function is controlled by the display and navigation module display.

6. CHECK COLOR BAR

HINT
* The display color on the screen is checked in the following procedure.
* Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be exactly the same as on the actual vehicle screen.

(a) Enter diagnostic mode Reading and Clearing Diagnostic Trouble Codes.

(b) Select "Function Check/Setting" from the "Service Menu" screen.





(c) Select "Color Bar" from the "Function Check/Setting" screen.





(d) Color Bar Check Mode

(1) Select a color bar from the "Color Bar Check Mode" screen.





(2) Check the display color.

HINT
* The entire screen turns to the color or stripe selected.
* Touching the display returns to the "Color Bar Check" screen.

7. CHECK GPS & VEHICLE SENSORS

HINT
* GPS information, vehicle signals and sensor signals are checked in the following procedure.
* Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be exactly the same as on the actual vehicle screen.

(a) Enter diagnostic mode Reading and Clearing Diagnostic Trouble Codes.

(b) Select "Function Check/Setting" from the "Service Menu" screen.





(c) Select "GPS & Vehicle Sensors" from the "Function Check/Setting" screen.





(d) GPS information

(1) When GPS information is displayed, check the GPS conditions.





HINT
* The signals from the vehicle sensors are updated once per second and if any have changed, the screen is updated.
* For details of this function, refer to Diagnosis Display Detailed Description in System Description System Description.

(e) Select "Sensors Check" from the "GPS Information" screen.

(f) Vehicle Sensors

(1) Check all the signals and sensors when vehicle signal information is displayed.





HINT
* The signals from the vehicle sensors are updated once per second and if any have changed, the screen is updated.
* This screen displays vehicle signals input to the display and navigation module display.
* For details of this function, refer to Diagnosis Display Detailed Description in System Description System Description.

8. CHECK VEHICLE SIGNAL

HINT
* Vehicle signals received by the display and navigation module display are checked in the following procedure.
* Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be exactly the same as on the actual vehicle screen.

(a) Enter diagnostic mode Reading and Clearing Diagnostic Trouble Codes.

(b) Select "Function Check/Setting" from the "Service Menu" screen.





(c) Select "Vehicle Signal" from the "Function Check/Setting" screen.





(d) Vehicle Signal Check Mode

(1) When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.





HINT
* Only conditions having inputs are displayed.
* This screen displays vehicle signals input to the display and navigation module display.
* For details of this function, refer to Diagnosis Display Detailed Description in System Description System Description.

9. CHECK HANDSFREE VOLUME SETTING

HINT
* The handsfree volume of a "Bluetooth" compatible phone can be adjusted using the following procedure.
* Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be exactly the same as on the actual vehicle screen.

(a) Enter diagnostic mode Reading and Clearing Diagnostic Trouble Codes.

(b) Select "Function Check/Setting" from the "Service Menu" screen.





(c) Select "Hands-free Volume Setting" from the "Function Check/Setting" screen.





(d) Hands-free Volume Setting

(1) Check the handsfree volume level.





Screen Description





NOTICE:
Sound quality may deteriorate when the receive voice level is changed more than necessary. For this reason, check that the received voice quality is still acceptable after changing this setting.

HINT
Sound quality of sent voice may deteriorate when the send voice level is adjusted.