Operation Check

DOOR LOCK: WIRELESS DOOR LOCK CONTROL SYSTEM: OPERATION CHECK

1. NOTICES WHEN CHECKING

(a) Wireless door lock/unlock function:

The wireless door lock control function operates only when the following conditions are met:

* The engine switch is off.

* All the doors are closed.

HINT
The unlock function operates even when one of the doors is open.

* There is no electrical key transmitter in the cabin.

* The power door lock control system is functioning normally.

* The function is not disabled by customization.

(b) The operational area of the wireless transmitter differs depending on the situation.

* The operational area differs depending on the user, the way the transmitter is held and the location.

* In certain areas, the operational area will be reduced due to the vehicle body shape and the influence of the surrounding environment.

* The weak electric waves from the transmitter may be affected if the area has strong electric waves or noise. The operational area of the transmitter may be reduced or the transmitter may not function.

* When the battery weakens, the operational area is reduced or the transmitter may not function.

HINT
The battery may weaken or other problems may occur if one of the following occurs: 1) the transmitter has had prolonged exposure to direct sunlight, such as on the instrument panel; or 2) the transmitter is placed within 1 m (3.28 ft) of electrical products, such as TVs, computers, cordless phones, cell phone recharger stands (with the cell phone recharging), etc.

2. CHECK WIRELESS DOOR LOCK CONTROL SYSTEM

HINT
* The switches described below transmit signals and are built into the electrical key transmitter.
* The operational area of the transmitter must be taken into account while checks are being made.

(a) Make sure the vehicle is in a condition in which the wireless door lock control functions can be operated (see above).

(b) Check the basic functions:

* Check that the transmitter LED illuminates 3 times when each switch is pressed 3 times.

HINT
If the LED does not illuminate when a switch has been pressed 3 times or more, the battery may be depleted.

* Check that when the lock switch is pressed, all the doors lock.

* Check that when the unlock switch is pressed once, only the driver side door unlocks. When the unlock switch is pressed again within 3 seconds, check that all doors unlock (unlock 2 operation)*.

HINT
*: The unlock 2 operation applies only if this function is set to on (the default setting).

* Check that when the glass hatch open switch is pressed for approximately 1 second or more, the glass hatch opens.

(c) Check the chattering prevention function:

* If a switch is pressed, check that the corresponding operation is performed only once. If the switch is held down, check that the corresponding operation occurs only once and does not repeatedly activate. Lastly, if a switch is pressed at 1 second intervals, check that the corresponding operation activates once for every press of the switch.

(d) Check the answer-back function:

* When the lock switch is pressed, check that the hazard warning lights flash once and the buzzer sounds once simultaneously with the locking operation of all the doors.

* When the unlock switch is pressed once, check that the hazard warning lights flash twice and the buzzer sounds twice simultaneously with the unlocking operation of all the doors.

(e) Check the automatic lock function:

* When all of the doors are unlocked with the unlock switch and none of the doors are opened or locked within 60 seconds*, check that the doors lock again.

HINT
*: The automatic lock function time (60 seconds) applies only if the setting of this function is set to the default setting.

(f) Check the switch operation fail-safe function:

* If the key is in the vehicle, check that the doors cannot be locked by the lock switch. However, this does not apply when the system is in recognition code registration mode.

(g) Check the illuminated entry function:

* When the map light door switch is on and all the doors are locked, check that pressing the unlock switch causes the interior light to illuminate and all the doors to unlock simultaneously.

* If the doors have not been opened, check that the interior light turns off in approximately 15 seconds.

(h) Check the door ajar warning function:

* If a door is open or not completely closed, check that the doors cannot be locked by the lock switch and the buzzer sounds for 10 seconds.

HINT
The buzzer stops sounding if one of the following conditions is met:

* The buzzer has sounded for 10 seconds.
* The engine switch is turned on (ACC) or on (IG).
* All the doors are closed.
* All the doors are unlocked by entry unlock operation or wireless operation.

(i) Check the panic alarm function.

* Check that the horn sounds, the headlights and taillights flash and the interior lights remain on (when the light switch is turned to the door position) for 60 seconds by the theft alarm function when the panic switch is held down for 0.8 seconds or more. Also, check that the horn stops sounding and the lights stop flashing when any switch of the transmitter is pressed.

(j) Check the memory call function Operation Check.