Installation

SEAT: REAR NO. 2 SEAT ASSEMBLY: INSTALLATION

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

NOTICE:
* Under either of the following conditions, perform initialization (initial position memorization) of the fold seat control ECU Rear Power Seat Control System.
* The fold seat control ECU is replaced with a new one.
* Initialization (initial position reset) of the fold seat control ECU is performed.
* Under any of the following conditions, perform initialization (initial position reset and initial position memorization) of the fold seat control ECU Rear Power Seat Control System.
* The fold seat control ECU is exchanged with one from another vehicle.
* The seatback frame and seat leg are inspected.
* The seat is disassembled and the positions of the seatback and seat cushion change with respect to one another.
* The seatback frame or seat leg is replaced.
* The cable is disconnected from the battery while the seatback or seat cushion is operating.

HINT
* Use the same procedure for the RH and LH sides.
* The procedure listed below is for the LH side.

1. INSTALL REAR NO. 2 SEAT ASSEMBLY LH

(a) Place the rear No. 2 seat assembly in the cabin.

NOTICE:
Be careful not to damage the vehicle body.

HINT
If installing the seat on the RH side with the LH side installed, install it with the No. 3 rear seat leg cover LH raised.

(b) Temporarily install the 4 bolts.

(c) Tighten the 4 bolts.

Torque : 37 Nm (377 kgf-cm, 27 ft-lbf)

(d) Attach the 6 claws and 2 guides to close the 2 covers.





Text in Illustration





(e) Connect the connector.

2. INSTALL NO. 1 DECK BOARD BRACKET LH

(a) Install the bracket with the 2 bolts.

3. INSTALL DECK BOARD BRACKET REINFORCEMENT

(a) Attach the 2 hooks.

(b) Install the reinforcement with the 2 bolts.

4. INSTALL REAR FLOOR MAT SUPPORT PLATE

(a) Attach the 5 clips and 4 guides.

(b) Attach the 6 claws to install the plate.

(c) Install the 3 bolts.

5. INSTALL REAR NO. 3 FLOOR BOARD (w/o Rear Air Conditioning System)

(a) Attach the 2 guides and 4 claws.





Text in Illustration





(b) Attach the clip to install the board.

6. INSTALL REAR NO. 3 FLOOR BOARD (w/ Rear Air Conditioning System)

(a) Attach the 2 guides and 4 claws.





Text in Illustration





(b) Attach the clip to install the board.

7. INSTALL REAR NO. 4 FLOOR BOARD

(a) Attach the 2 guides and 4 claws.





Text in Illustration





(b) Attach the clip to install the board.

8. INSTALL DECK BOARD ASSEMBLY

(a) Attach the 4 clips.

(b) Install the deck board with the 2 bolts.

(c) Attach the 2 claws to close the cover.





HINT
Use the same procedure to close the cover on the other side.

9. PERFORM INITIALIZATION

NOTICE:
* Under either of the following conditions, perform initialization (initial position memorization) of the fold seat control ECU Rear Power Seat Control System.
* The fold seat control ECU is replaced with a new one.
* Initialization (initial position reset) of the fold seat control ECU is performed.
* Under any of the following conditions, perform initialization (initial position reset and initial position memorization) of the fold seat control ECU Rear Power Seat Control System.
* The fold seat control ECU is exchanged with one from another vehicle.
* The seatback frame and seat leg are inspected.
* The seat is disassembled and the positions of the seatback and seat cushion change with respect to one another.
* The seatback frame or seat leg is replaced.
* The cable is disconnected from the battery while the seatback or seat cushion is operating.

10. CHECK REAR NO. 2 SEAT

(a) Check the power seat operation Operation Check.