Driver Side Door Entry Lock Function Does Not Operate

THEFT DETERRENT / KEYLESS ENTRY: SMART ACCESS SYSTEM WITH PUSH-BUTTON START (for Entry Function): Driver Side Door Entry Lock Function does not Operate
- Driver Side Door Entry Lock Function does not Operate

DESCRIPTION

If the driver door entry unlock function operates normally, but its entry lock function does not, this means that the request code from the driver door is being output normally. In this case, a malfunction in the lock switch circuit (from the certification ECU (smart key ECU assembly) to the front door outside handle assembly (lock switch)) is suspected.

WIRING DIAGRAM





INSPECTION PROCEDURE

NOTICE:
* The smart access system with push-button start (for entry function) uses a LIN communication system and BEAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting How To Proceed With Troubleshooting. Troubleshoot the smart access system with push-button start (for entry function) after confirming that the communication system is functioning properly.
* Confirm that another key is not in the cabin.

PROCEDURE

1. CHECK POWER DOOR LOCK OPERATION

(a) When the door control switch on the master switch assembly is operated, check that the doors unlock and lock according to switch operation Operation Check.

OK:

Door locks operate normally.

NG -- GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Problem Symptoms Table) Problem Symptoms Table
OK -- Continue to next step.

2. READ VALUE USING TECHSTREAM (DOOR UNLOCK DETECTION SWITCH)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Master Switch / Data List.

(e) Read the Data List according to the display on the Techstream.

Master Switch (Power Window Regulator Master Switch Assembly)





OK:

On the Techstream screen, the display changes between ON and OFF according to the chart above.

Result:





B -- GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Problem Symptoms Table) Problem Symptoms Table
A -- Continue to next step.

3. READ VALUE USING TECHSTREAM (DOOR OUTSIDE HANDLE)

(a) Enter the following menus: Body Electrical / Smart Access / Data List.

(b) Read the Data List according to the display on the Techstream.

Smart Access (Certification ECU (Smart Key ECU Assembly))





OK:

On the Techstream screen, the display changes between ON and OFF according to the chart above.

NG -- CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - DOOR ELECTRICAL KEY OSCILLATOR)

OK -- REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) Removal

4. CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - DOOR ELECTRICAL KEY OSCILLATOR)

(a) Disconnect the front door outside handle assembly (for driver side) connector.

(b) Disconnect the door electrical key oscillator (for driver side) connector.





(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.

5. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE)

(a) Disconnect the certification ECU (smart key ECU assembly) connector.





(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.

6. INSPECT FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Driver Side)

(a) Measure the resistance according to the value(s) in the table below.





Standard Resistance:





Text in Illustration





NG -- REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Driver Side) Removal
OK -- Continue to next step.

7. REPLACE DOOR ELECTRICAL KEY OSCILLATOR (for Driver Side)

(a) Replace the door electrical key oscillator (for driver side) Removal.

NEXT -- Continue to next step.

8. CHECK DOOR ELECTRICAL KEY OSCILLATOR (DRIVER SIDE OPERATION)

(a) Check that the entry functions operate normally Operation Check.

OK:

Entry functions operate normally.

NG -- REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) Removal

OK -- END (DOOR ELECTRICAL KEY OSCILLATOR WAS DEFECTIVE)