Luggage Compartment Door Entry Unlock Function Does Not Operate When Key Is Outside Luggage Compartment

THEFT DETERRENT / KEYLESS ENTRY: SMART ACCESS SYSTEM WITH PUSH-BUTTON START (for Entry Function): Luggage Compartment Door Entry Unlock Function does not Operate when Key is Outside Luggage Compartment
- Luggage Compartment Door Entry Unlock Function does not Operate when Key is Outside Luggage Compartment

DESCRIPTION

When the entry luggage compartment open function does not operate, one of the following may be the cause: 1) luggage compartment door opener outer switch malfunction; 2) communication malfunction with the outside electrical key oscillator (luggage compartment); 3) the main body ECU LH (cowl side junction block LH) receives the luggage compartment door opener outer switch ON signal, but is unable to send the signal to the certification ECU (smart key ECU assembly) through BEAN communication; or 5) certification ECU (smart key ECU assembly) malfunction.

WIRING DIAGRAM

INSPECTION PROCEDURE

PROCEDURE

1. READ VALUE USING TECHSTREAM (LUGGAGE COMPARTMENT DOOR OPEN MODE)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Smart Access / Data List.

(e) Read the Data List according to the display on the Techstream.

Smart Access (Certification ECU (Smart Key ECU Assembly))

Result:

A -- PERFORM CUSTOMIZE SETTING Smart Access System With Push-Button Start (for Entry Function)
B -- Continue to next step.

2. CHECK LUGGAGE COMPARTMENT DOOR OPENER SYSTEM (OPEN OPERATION)

(a) When the luggage compartment door opener inner switch is operated, check that the luggage compartment door opens Operation Check.

OK:

Luggage compartment door opens.

NG -- GO TO LUGGAGE COMPARTMENT DOOR OPENER SYSTEM (Luggage Compartment Door Opener does not Operate) Luggage Compartment Door Opener Does Not Operate
OK -- Continue to next step.

3. READ VALUE USING TECHSTREAM (LUGGAGE COMPARTMENT DOOR OPENER SWITCH)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Body No. 3 / Data List.

(e) Read the Data List according to the display on the Techstream.

Body No. 3 (Main Body ECU LH (Cowl Side Junction Block LH))

OK:

On the Techstream screen, the display changes between ON and OFF according to the chart above.

NG -- INSPECT LUGGAGE COMPARTMENT DOOR OPENER OUTER SWITCH
OK -- Continue to next step.

4. CHECK WAVE ENVIRONMENT

(a) Bring the electrical key transmitter near the outside electrical key oscillator (luggage compartment), and perform an entry luggage compartment open function check.

NOTICE:
If the key is brought within 0.2 m (0.656 ft) of the rear bumper, communication is not possible.

HINT
* When the electrical key transmitter is brought near the outside electrical key oscillator (luggage compartment), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
* If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

OK:

Entry functions operate normally.

NG -- PERFORM KEY DIAGNOSTIC MODE INSPECTION

OK -- AFFECTED BY WAVE INTERFERENCE

5. PERFORM KEY DIAGNOSTIC MODE INSPECTION

(a) Diagnostic mode inspection (outside electrical key oscillator (luggage compartment))

(1) Connect the Techstream to the DLC3.

(2) Turn the engine switch on (IG).

(3) Turn the Techstream on.

(4) Enter the following menus: Body Electrical / Smart Access / Utility / Communication Check (Key Diag Mode) / Overhead + Luggage (outside).

(5) When the electrical key transmitter is held at the same height as the rear bumper upper surface aligning it with the center of the rear of the vehicle, check that the wireless door lock buzzer sounds.

HINT
If the buzzer sounds, it can be determined that the luggage compartment exterior transmitter is operating normally.

OK:

Wireless door lock buzzer sounds.

NG -- CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - OUTSIDE ELECTRICAL KEY OSCILLATOR)

OK -- REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) Removal

6. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - OUTSIDE ELECTRICAL KEY OSCILLATOR)

(a) Disconnect the certification ECU (smart key ECU assembly) connector.

(b) Disconnect the outside electrical key oscillator (luggage compartment) connector.

NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.

7. REPLACE OUTSIDE ELECTRICAL KEY OSCILLATOR (LUGGAGE COMPARTMENT)

(a) Replace the outside electrical key oscillator (luggage compartment) Removal.

NEXT -- Continue to next step.

8. CHECK OUTSIDE ELECTRICAL KEY OSCILLATOR (LUGGAGE COMPARTMENT OPERATION)

(a) Check that the entry functions operate normally Operation Check.

OK:

Entry functions operate normally.

NG -- REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) Removal

OK -- END (OUTSIDE ELECTRICAL KEY OSCILLATOR IS DEFECTIVE)

9. INSPECT LUGGAGE COMPARTMENT DOOR OPENER OUTER SWITCH

(a) Remove the luggage compartment door opener outer switch Removal.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

NG -- REPLACE LUGGAGE COMPARTMENT DOOR OPENER OUTER SWITCH Removal
OK -- Continue to next step.

10. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU LH - OPENER SWITCH)

(a) Disconnect the main body ECU LH (cowl side junction block LH) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR

OK -- REPLACE MAIN BODY ECU LH (COWL SIDE JUNCTION BLOCK LH)