Front Passenger Side Power Window Does Not Operate With Front Passenger Side Power Window Switch
WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch
- Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch
DESCRIPTION
When the hybrid vehicle control system is running or the power switch is on (IG), the power window regulator motor assembly (for front passenger side) is operated by the power window regulator switch assembly (for front passenger side). The power window regulator motor assembly (for front passenger side) has motor, regulator, and ECU functions.
HINT
If the pulse sensor built into the power window regulator motor assembly (for front passenger side) malfunctions, the power window control system enters fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the power window regulator switch assembly (for front passenger side) at the auto up position, and opened manually by pushing down the power window regulator switch assembly (for front passenger side).
WIRING DIAGRAM
INSPECTION PROCEDURE
NOTICE:
* The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting How To Proceed With Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.
* When the power window regulator motor assembly (for front passenger side) is reinstalled or replaced, the power window control system must be initialized Initialization.
* After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be reinitialized by repeating the following operations at least 5 times:
(1) Close the power window by fully pulling up the power window regulator switch assembly (for front passenger side) and holding it at the auto up position.
(2) Open the power window by fully pushing down the power window regulator switch assembly (for front passenger side).
* When the ECU determines that the power window regulator motor assembly (for front passenger side) has a malfunction, DTC B2311 is set.
PROCEDURE
1. READ VALUE USING TECHSTREAM (Main Body)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Main Body / Data List.
(e) Read the Data List according to the display on the Techstream.
Main Body (Main Body ECU (Multiplex Network Body ECU))
OK:
On the Techstream screen, OK is displayed.
NG -- GO TO LIN COMMUNICATION SYSTEM (Proceed to How to Proceed with Troubleshooting) How to Proceed With Troubleshooting
OK -- Continue to next step.
2. READ VALUE USING TECHSTREAM (P-Door Motor)
(a) Enter the following menus: Body Electrical / P-Door Motor / Data List.
(b) Read the Data List according to the display on the Techstream.
P-Door Motor (Power Window Regulator Motor Assembly (for Front Passenger Side))
OK:
On the Techstream screen, ON or OFF is displayed accordingly.
NG -- INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)
OK -- Continue to next step.
3. PERFORM ACTIVE TEST USING TECHSTREAM (P-Door Motor)
(a) Enter the following menus: Body Electrical / P-Door Motor / Active Test.
(b) Perform the Active Test according to the display on the Techstream.
P-Door Motor (Power Window Regulator Motor Assembly (for Front Passenger Side))
OK:
Front passenger side power window operates normally.
CAUTION:
Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.
NG -- REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Side) Removal
OK -- REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Removal
4. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)
(a) Remove the power window regulator switch assembly (for front passenger side) Removal.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
NG -- REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side) Removal
OK -- Continue to next step.
5. CHECK HARNESS AND CONNECTOR (FRONT PASSENGER SIDE SWITCH - MOTOR AND BODY GROUND)
(a) Disconnect the power window regulator motor assembly (for front passenger side) connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Side) Removal