SFI System
2GR-FSE ENGINE CONTROL: SFI SYSTEM: P0500: Vehicle Speed Sensor "A"
P0500 - Vehicle Speed Sensor "A"
DESCRIPTION
The wheel speed sensors monitor the wheel rotation speed and send signals to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter assembly. The ECM determines the vehicle speed based on the frequency of the pulse signal.
HINT
- A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.
- If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the wiring diagram below will not operate normally.
MONITOR DESCRIPTION
If there is no speed signal from the combination meter assembly even though the ECM determines that the vehicle is being driven, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and sets the DTC.
MONITOR STRATEGY
TYPICAL ENABLING CONDITIONS
TYPICAL MALFUNCTION THRESHOLDS
CONFIRMATION DRIVING PATTERN
1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG) and turn the Techstream on.
3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure) Reading and Clearing Diagnostic Trouble Codes.
4. Turn the engine switch off and wait for at least 30 seconds.
5. Turn the engine switch on (IG) and turn the Techstream on [A].
6. Start the engine.
7. Drive the vehicle at 24 km/h (15 mph) or more for a total of 30 seconds or more [B].
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
8. Stop the vehicle.
9. Enter the following menus: Powertrain / Engine / Trouble Codes [C].
10. Read Pending DTCs.
HINT
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
12. Input the DTC: P0500.
13. Check the DTC judgment result.
HINT
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
14. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs Reading and Clearing Diagnostic Trouble Codes.
HINT
- If a permanent DTC is output, the system is malfunctioning.
- If no permanent DTC is output, the system is normal.
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
1. CHECK OPERATION OF SPEEDOMETER
(a) Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.
HINT
- The vehicle speed sensor is operating normally if the speedometer reading is normal.
- If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction.
NG -- GO TO METER / GAUGE SYSTEM (SPEEDOMETER MALFUNCTION) How To Proceed With Troubleshooting
OK -- Continue to next step.
2. READ VALUE USING TECHSTREAM (VEHICLE SPEED)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Data List / Vehicle Speed.
(e) Drive the vehicle.
(f) Read the value displayed on the Techstream.
OK:
Vehicle speeds displayed on the Techstream and speedometer display are equal.
NG -- CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
OK -- CHECK FOR INTERMITTENT PROBLEMS Check for Intermittent Problems
3. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
(a) Disconnect the combination meter assembly connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Open):
(d) Reconnect the combination meter assembly connector.
(e) Reconnect the ECM connector.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
OK -- Continue to next step.
4. CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)
(a) Disconnect the combination meter assembly connector.
HINT
Disconnect the ECU connectors on the other systems related to the speed signal (but the ECM connectors must be connected).
(b) Turn the engine switch on (IG).
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Text in Illustration
(d) Reconnect the combination meter assembly connector.
NG -- REPLACE ECM Removal
OK -- Continue to next step.
5. CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL OUTPUT WAVEFORM)
(a) Remove the combination meter assembly.
(b) Connect the combination meter assembly connector.
(c) Move the shift lever to N.
(d) Jack up the vehicle.
(e) Turn the engine switch on (IG).
(f) Check the voltage between the terminal of the combination meter assembly and the body ground while the wheel is turned slowly.
Standard Voltage:
Text in Illustration
HINT
The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.
(g) Reinstall the combination meter assembly.
NG -- CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM)
OK -- REPLACE ECM Removal
6. CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM)
(a) Remove the combination meter assembly.
(b) Connect the combination meter assembly connector.
(c) Move the shift lever to the neutral position.
(d) Jack up the vehicle.
(e) Turn the engine switch on (IG).
(f) Check the voltage between the terminal of the combination meter assembly and the body ground while the wheel is turned slowly.
Standard Voltage:
Text in Illustration
HINT
The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.
(g) Reinstall the combination meter assembly.
NG -- CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR)
OK -- REPLACE COMBINATION METER ASSEMBLY Removal
7. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR)
(a) Disconnect the combination meter assembly connector.
(b) Disconnect the brake actuator connector.
(c) Measure the resistance according the value(s) in the table below.
Standard Resistance (Check for Open):
Standard Resistance (Check for Short):
(d) Reconnect the combination meter assembly connector.
(e) Reconnect the brake actuator connector.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- REPLACE BRAKE ACTUATOR ASSEMBLY Removal