Fuel Pump Control Circuit
2GR-FSE ENGINE CONTROL: SFI SYSTEM: Fuel Pump Control Circuit
- Fuel Pump Control Circuit
DESCRIPTION
Refer to DTC P0230 P0230.
WIRING DIAGRAM
Refer to DTC P0230 P0230.
INSPECTION PROCEDURE
PROCEDURE
1. CHECK FUEL PUMP OPERATION
(a) Check the fuel pump operation Fuel System.
NG -- PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE CIRCUIT OPENING RELAY)
OK -- Continue to next step.
2. INSPECT F/PMP RELAY
(a) Inspect the F/PMP relay On-Vehicle Inspection.
NG -- REPLACE F/PMP RELAY
OK -- Continue to next step.
3. INSPECT FUEL PUMP RESISTOR
(a) Inspect the fuel pump resistor Testing and Inspection.
NG -- REPLACE FUEL PUMP RESISTOR Removal
OK -- Continue to next step.
4. CHECK HARNESS AND CONNECTOR (F/PMP RELAY - FUEL PUMP RESISTOR)
(a) Remove the F/PMP relay from the engine room No. 2 relay block.
(b) Disconnect the fuel pump resistor connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Open):
Standard Resistance (Check for Short):
(d) Reinstall the F/PMP relay.
(e) Reconnect the fuel pump resistor connector.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Symptom Related Diagnostic Procedures
5. PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE CIRCUIT OPENING RELAY)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG) and turn the Techstream on.
(c) Enter the following menus: Powertrain / Engine / Active Test / Activate the Fuel Pump Speed Control.
(d) Check the operation of the relay while operating it using the Techstream.
OK:
Operating noise can be heard from the C/OPN relay.
NG -- INSPECT INTEGRATION RELAY (EFI NO. 2 RELAY)
OK -- Continue to next step.
6. INSPECT FUEL PUMP
(a) Inspect the fuel pump Fuel Pump.
NG -- REPLACE FUEL PUMP Removal
OK -- Continue to next step.
7. CHECK HARNESS AND CONNECTOR (FUEL PUMP - F/PMP RELAY)
(a) Disconnect the fuel pump connector.
(b) Remove the F/PMP relay from the engine room No. 2 relay block.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Open):
Standard Resistance (Check for Short):
(d) Reinstall the F/PMP relay.
(e) Reconnect the fuel pump connector.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL PUMP - F/PMP RELAY)
OK -- Continue to next step.
8. CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)
(a) Disconnect the fuel pump connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Open):
Text in Illustration
(c) Reconnect the fuel pump connector.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL PUMP - BODY GROUND)
OK -- Continue to next step.
9. CHECK HARNESS AND CONNECTOR (C/OPN RELAY - F/PMP RELAY)
(a) Remove the integration relay from the engine room No. 2 relay block.
(b) Remove the F/PMP relay from the engine room No. 2 relay block.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Open):
(d) Disconnect the fuel pump resistor connector.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Short):
Text in Illustration
(f) Reinstall the relays.
(g) Reconnect the fuel pump resistor connector.
NG -- REPLACE ENGINE ROOM RELAY BLOCK NO. 2
OK -- REPAIR OR REPLACE FUEL SYSTEM
10. INSPECT INTEGRATION RELAY (EFI NO. 2 RELAY)
(a) Inspect the EFI No. 2 relay Inspection.
NG -- REPLACE INTEGRATION RELAY Removal
OK -- Continue to next step.
11. INSPECT INTEGRATION RELAY (C/OPN RELAY)
(a) Inspect the C/OPN relay Inspection.
NG -- REPLACE INTEGRATION RELAY Removal
OK -- Continue to next step.
12. INSPECT ECM (FC VOLTAGE)
(a) Turn the engine switch on (IG).
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Text in Illustration
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - C/OPN RELAY)
OK -- REPLACE ECM Removal