Operation CHARM: Car repair manuals for everyone.

Installation





WIPER / WASHER: FRONT WIPER MOTOR: INSTALLATION

1. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

(a) Using a T30 "TORX" socket wrench, install the windshield wiper motor assembly with the 2 bolts and 2 nuts.





Torque : 7.5 Nm (77 kgf-cm, 66 in-lbf)

(b) Apply MP grease to the crank arm pivot of the windshield wiper motor assembly.





(c) Install the No. 1 windshield wiper link rod to the crank arm pivot of the windshield wiper motor assembly as shown in the illustration.

(d) Apply MP grease to the pivot of the windshield wiper link assembly.





(e) Install the No. 1 windshield wiper link rod to the pivot of the windshield wiper link assembly as shown in the illustration.

(f) Install the No. 2 windshield wiper link rod to the crank arm pivot of the windshield wiper motor assembly as shown in the illustration.





2. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

(a) Engage the rubber pin to install the windshield wiper motor and link assembly as shown in the illustration.





(b) Install the windshield wiper motor and link assembly with the 2 bolts.





Torque : 5.5 Nm (56 kgf-cm, 49 in-lbf)

(c) Connect the connector.

3. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

(a) Install the rear side 7 guides.





(b) Engage the 3 claws and front side guide to install the cowl top ventilator louver sub-assembly as shown in the illustration.

(c) Install the 2 clips.





4. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

(a) Operate the wiper, and stop the windshield wiper motor at the automatic stop position.

(b) When reusing the front wiper arm and blade assembly LH:





(1) Clean the wiper arm serrations.

(c) When reusing the windshield wiper link assembly:

(1) Clean the wiper pivot serrations with a wire brush.

Text in Illustration





(d) Install the front wiper arm and blade assembly LH with the nut at the position as shown in the illustration.





Torque : 22 Nm (224 kgf-cm, 16 ft-lbf)

HINT
Hold the arm hinge by hand to tighten the nut.





Text in Illustration





5. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

(a) Operate the wiper, and stop the windshield wiper motor at the automatic stop position.

(b) When reusing the front wiper arm and blade assembly RH:





(1) Clean the wiper arm serrations.

(c) When reusing the windshield wiper link assembly:

(1) Clean the wiper pivot serrations with a wire brush.

Text in Illustration





(d) Install the front wiper arm and blade assembly RH with the nut at the position as shown in the illustration.





Torque : 22 Nm (224 kgf-cm, 16 ft-lbf)

HINT
Hold the arm hinge by hand to tighten the nut.





Text in Illustration





(e) Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.

6. INSTALL FRONT WIPER ARM HEAD CAP

(a) Install the front wiper arm head cap.





HINT
Use the same procedure for the RH side and LH side.

7. INSTALL FRONT OUTER BODY PILLAR ASSEMBLY LH Installation

8. INSTALL ROOF DRIP SIDE FINISH MOULDING LH Installation

9. INSTALL FRONT OUTER BODY PILLAR ASSEMBLY RH

HINT
Use the same procedure for the RH side and LH side.

10. INSTALL ROOF DRIP SIDE FINISH MOULDING RH

HINT
Use the same procedure for the RH side and LH side.

11. INSTALL ROOF HEADLINING ASSEMBLY

(a) Install the roof headlining assembly Installation.

12. INSTALL FRONT UPPER FENDER PROTECTOR LH

(a) Engage the claw and the 3 clips then install the front upper fender protector LH.





(b) Engage the clip on the rubber portion of the cowl top ventilator louver sub-assembly to the front upper fender protector LH.

13. INSTALL FRONT UPPER FENDER PROTECTOR RH

HINT
Use the same procedure for the RH side and LH side.

14. INSTALL ENGINE ROOM SIDE COVER LH

(a) Install the side cover with the 4 clips and grommet.





Text in Illustration





15. INSTALL ENGINE ROOM SIDE COVER RH

(a) Install the side cover RH with the clip and grommet.





Text in Illustration





16. INSTALL COOL AIR INTAKE DUCT SEAL Installation