Reassembly
EXTERIOR PANELS / TRIM: FRONT BUMPER: REASSEMBLY
1. INSTALL FRONT BUMPER REINFORCEMENT
(a) Install the front bumper reinforcement with the 6 bolts.
Torque : 70 Nm (714 kgf-cm, 52 ft-lbf)
(b) Install the cooler (ambient temp sensor) thermistor with the clamp.
(c) Install the radiator support opening cover with the 2 clips.
2. INSTALL FRONT BUMPER ENERGY ABSORBER
(a) Install the front bumper energy absorber.
3. INSTALL FRONT BUMPER SIDE RETAINER LH
(a) Engage the 2 claws and install the front bumper side retainer LH.
(b) Install the screw.
4. INSTALL FRONT BUMPER SIDE RETAINER RH
HINT
Use the same procedure for the RH side and LH side.
5. INSTALL FRONT FENDER LINER RETAINER
(a) Engage the 2 claws and install the 2 front fender liner retainers.
HINT
Use the same procedure for the RH side and LH side.
6. INSTALL LOWER FRONT BUMPER COVER
(a) Engage the 2 claws and install the lower front bumper cover.
7. INSTALL FOG LIGHT COVER LH
(a) Engage the 4 claws and install the fog light cover LH.
8. INSTALL FOG LIGHT COVER RH
HINT
Use the same procedure for the RH side and LH side.
9. INSTALL LOWER RADIATOR GRILLE
(a) Engage the 14 claws and install the lower radiator grille.
10. INSTALL RADIATOR GRILLE EMBLEM (w/o Dynamic Radar Cruise Control System)
HINT
When installing the radiator grille emblem, heat the radiator grille and radiator grille emblem using a heat light.
Heating Temperature
NOTICE:
Do not heat the radiator grille and radiator grille emblem excessively.
(a) Clean the radiator grille surface.
(1) Using a heat light, heat the radiator grille surface.
(2) Remove the double-sided tape from the radiator grille.
(3) Wipe off any tape adhesive residue with cleaner.
(b) Clean the radiator grille emblem (if reusing the radiator grille emblem).
(1) Using a heat light, heat the radiator grille emblem.
(2) Remove the double-sided tape from the radiator grille emblem.
(3) Wipe off any tape adhesive residue with cleaner.
(4) Apply new double-sided tape to the radiator grille emblem.
(c) Install the radiator grille emblem.
(1) Using a heat light, heat the radiator grille and radiator grille emblem.
(2) Remove the peeling paper from the face of the radiator grille emblem.
HINT
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
(3) Install the radiator grille emblem.
11. INSTALL RADIATOR GRILLE EMBLEM (w/ Dynamic Radar Cruise Control System)
(a) Engage the claw and install the radiator grille emblem.
(b) Install the 2 spring nuts.
12. INSTALL RADIATOR GRILLE
(a) Engage the 6 claws and install the radiator grille.
(b) Install the 2 clips.
13. INSTALL RADIATOR GRILLE ASSEMBLY
(a) Engage the 15 claws and 2 guides, and install the radiator grille assembly.
(b) Install the 2 clips.
14. INSTALL RADIATOR GRILLE PROTECTOR
(a) Engage the 15 claws and install the radiator grille protector.
15. INSTALL HEADLIGHT HOSE (w/ Headlight Cleaner System)
(a) Engage the 7 clamps and install the headlight hose.
16. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System) Installation
17. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)
HINT
Use the same procedure for the RH side and LH side.
18. INSTALL HEADLIGHT CLEANER WASHER NOZZLE LH (w/ Headlight Cleaner System) Installation
19. INSTALL HEADLIGHT CLEANER WASHER NOZZLE RH (w/ Headlight Cleaner System)
HINT
Use the same procedure for the RH side and LH side.
20. INSTALL NO. 4 ENGINE ROOM WIRE (w/ Intuitive Parking Assist System)
(a) Engage the 13 clamps and install the No. 4 engine room wire.
21. INSTALL NO. 3 ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System)
Installation
HINT
Use the same procedure for the RH side and LH side.
22. INSTALL NO. 1 ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)
Installation
HINT
Use the same procedure for the RH side and LH side.
23. INSTALL FOG LIGHT ASSEMBLY LH Installation
24. INSTALL FOG LIGHT ASSEMBLY RH
HINT
Use the same procedure for the RH side and LH side.