Rear Door RH Entry Lock and Unlock Functions Do Not Operate

DOOR LOCK: SMART ACCESS SYSTEM WITH PUSH-BUTTON START: Rear Door RH Entry Lock and Unlock Functions do not Operate
- Rear Door RH Entry Lock and Unlock Functions do not Operate

DESCRIPTION

When the rear door RH entry lock and unlock functions do not operate, one of the following may be malfunctioning: 1) power door lock system, 2) rear door RH electrical key oscillator, or 3) certification ECU.

WIRING DIAGRAM





INSPECTION PROCEDURE

NOTICE:
Before performing the inspection, check that there are no problems related to the "CAN COMMUNICATION SYSTEM" and "LIN COMMUNICATION SYSTEM".

PROCEDURE

1. CHECK POWER DOOR LOCK OPERATION

(a) When the master switch's door control switch is operated, check that the locked doors unlock Operation Check.

OK:

Locked doors unlock.

NG -- GO TO POWER DOOR LOCK CONTROL SYSTEM Problem Symptoms Table
OK -- Continue to next step.

2. READ VALUE USING TECHSTREAM (DOOR LOCK POSITION SWITCH)

(a) Using the Techstream, read the Data List Smart Access System With Push-Button Start.

Rear Right Door





OK:

On the Techstream screen, item changes between ON and OFF according to above chart.

NG -- GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Rear Door RH LOCK/UNLOCK Functions do not Operate) Problem Symptoms Table
OK -- Continue to next step.

3. READ VALUE USING TECHSTREAM

(a) Using the Techstream, read the Data List Smart Access System With Push-Button Start.

Rear Right Door





OK:

On the Techstream screen, item changes between ON and OFF according to above chart.

NG -- CHECK REAR DOOR ECU RH
OK -- Continue to next step.

4. CHECK WAVE ENVIRONMENT

(a) Bring the electrical key transmitter near the rear door outside handle RH, and perform a rear right door entry lock and unlock operation check.





NOTICE:
If the key is brought within 0.2 m (0.656 ft.) of the door handle, communication is not possible.

HINT
* When the electrical key transmitter is brought near the rear right passenger door outside handle, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
* If the inspection result is that the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

OK:

Entry functions operate normally.

NG -- KEY DIAGNOSTIC MODE

OK -- AFFECTED BY WAVE INTERFERENCE

5. KEY DIAGNOSTIC MODE

(a) Diagnostic mode inspection door electrical key oscillator





(1) Connect the Techstream to the DLC3.

(2) Turn the power switch ON (IG).

(3) Turn the Techstream on.

(4) Enter the following menus: Body Electrical/ Smart Access / Smart Communication Check /Overhead + Driver Side Rear.

(5) When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.

HINT
If the buzzer sounds, it can be determined that the rear right seat outside transmitter is operating normally.

OK:

Wireless door lock buzzer sounds

NG -- CHECK HARNESS AND CONNECTOR (REAR DOOR ECU RH - CERTIFICATION ECU)

OK -- END (CERTIFICATION ECU IS DEFECTIVE)

6. CHECK HARNESS AND CONNECTOR (REAR DOOR ECU RH - CERTIFICATION ECU)





(a) Disconnect the O3 ECU connector.

(b) Disconnect the L16 ECU connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.

7. CHECK HARNESS AND CONNECTOR (REAR DOOR ECU RH - ELECTRICAL KEY OSCILLATOR)





(a) Disconnect the O4 ECU connector.

(b) Disconnect the c2 oscillator connector

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.

8. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR)





(a) Disconnect the L16 ECU connector.

(b) Disconnect the c2 oscillator connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.

9. CHECK HARNESS AND CONNECTOR (REAR DOOR ECU RH - DOOR ELECTRICAL KEY OSCILLATOR)





(a) Disconnect the O3 ECU connector.

(b) Disconnect the c2 oscillator connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.

10. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - REAR DOOR OUTSIDE HANDLE RH)





(a) Disconnect the c2 oscillator connector.

(b) Disconnect the c1 handle connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.

11. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)

(a) Replace the door electrical key oscillator with a new one or normally functioning one Components.

(b) Check that the entry function operates normally Operation Check.

OK:

Operates normally

NG -- CHECK REAR DOOR OUTSIDE HANDLE RH (OPERATION)

OK -- END (DOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE)

12. CHECK REAR DOOR OUTSIDE HANDLE RH (OPERATION)

(a) Replace the rear door outside handle RH with a new one or normally functioning one Removal.

(b) Check that the entry function operates normally Operation Check.

OK:

Operates normally

NG -- CHECK REAR DOOR ECU RH (OPERATION)

OK -- END (REAR DOOR OUTSIDE HANDLE RH IS DEFECTIVE)

13. CHECK REAR DOOR ECU RH (OPERATION)

(a) Replace the rear door ECU RH with a new one or normally functioning one Components.

(b) Check that the entry function operates normally Operation Check.

OK:

Operates normally

NG -- REPLACE CERTIFICATION ECU Removal

OK -- END (REAR DOOR ECU RH IS DEFECTIVE)

14. CHECK REAR DOOR ECU RH





(a) Measure the voltage according to the value(s) in the table below.

Standard voltage:





NG -- REPLACE REAR DOOR ECU RH Removal
OK -- Continue to next step.

15. CHECK HARNESS AND CONNECTOR (REAR DOOR ECU RH - DOOR ELECTRICAL KEY OSCILLATOR)





(a) Disconnect the O3 ECU connector.

(b) Disconnect the c2 oscillator connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.

16. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - REAR DOOR OUTSIDE HANDLE RH)





(a) Disconnect the c2 oscillator connector.

(b) Disconnect the c1 handle connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.

17. CHECK HARNESS AND CONNECTOR (REAR DOOR ECU RH - REAR DOOR OUTSIDE HANDLE RH)





(a) Disconnect the O3 ECU connector.

(b) Disconnect the c1 handle connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.

18. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)

(a) Replace the door electrical key oscillator with a new one or normally functioning one Components.

(b) Check that the entry function operates normally Operation Check.

OK:

Operates normally

NG -- CHECK REAR DOOR OUTSIDE HANDLE RH (OPERATION)

OK -- END (DOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE)

19. CHECK REAR DOOR OUTSIDE HANDLE RH (OPERATION)

(a) Replace the rear door outside handle RH with a new one or normally functioning one Removal.

(b) Check that the entry function operates normally Operation Check.

OK:

Operates normally

NG -- REPLACE REAR DOOR ECU RH Removal

OK -- END (REAR DOOR OUTSIDE HANDLE RH IS DEFECTIVE)