Rear Window Glass Installation

REAR WINDOW GLASS INSTALLATION

WARNING:
- Using a utility knife with bare hands can cause injury. Always wear gloves when using a utility knife.

CAUTION:
- Proper installation of the glass may be difficult if sealant is cracked or the glass is pushed out by air pressure when a door is opened/closed with all the window glass closed. Keep the door glass open until the rear window glass installation is completed.

4SD

1. Remove sealant along the perimeter of the glass using a utility knife or scraper. (When reusing the glass)

2. Clean and degrease an approx. 50 mm {2.0 in} wide strip along the perimeter of the glass.

3. Inspect the glass for cracks. If it is cracked, chamfer it using sandpaper.

4. Install the spacer and pins to the glass as shown in the figure.






NOTE:
- When reusing the glass, align it with the alignment mark placed before the glass was removed.

5. Install the rear window glass molding.






6. Apply glass primer on the glass as shown in the figure then allow it to dry for approx. 30 min.

CAUTION:
- To prevent weakening of the primer adhesion, keep the bonding surface free of dirt, moisture, and grease. Do not touch the surface with your hand.

NOTE:
- Apply primer to the hollowed marks in the ceramic coating.






7. Cut away the old sealant using a utility knife or scraper so that 1-2 mm {0.04-0.07 in} thickness of sealant remains along the perimeter of the frame.






8. Clean and degrease along the perimeter of the bonding area on the body.

9. If the sealant has come off completely in any one place, apply some primer, and allow it to dry for approx. 30 min.

CAUTION:
- To prevent weakening of the primer adhesion, keep the bonding surface free of dirt, moisture, and grease. Do not touch the surface with your hand.

10. Apply body primer on the body as shown in the figure, then allow it to dry for approx. 30 min.

CAUTION:
- To prevent weakening of the primer adhesion, keep the bonding surface free of dirt, moisture, and grease. Do not touch the surface with your hand.

NOTE:
- Apply primer to the hollowed marks in the ceramic coating.






11. Apply sealant to the area of the glass surface as shown in the figure.






12. Install the rear window glass.

13. Verify that the gap at the upper and lower parts of the glass is within the specification shown in the figure, then press along the perimeter of the glass.






14. Connect the filament connector.






15. Install the fasteners.






16. Install the following parts:
a. Tire house trims Tire House Trim Removal/Installation

b. Rear package trim Service and Repair

c. C-pillar trims C-Pillar Trim Removal/Installation

d. Rear side seat back Rear Seat Back Removal/Installation

e. Rear scuff plate Rear Scuff Plate Removal/Installation

f. Rear seat cushion Rear Seat Cushion Removal/Installation

17. Allow the sealant to harden completely. Sealant hardening time: 24 h

5HB

1. Remove sealant along the perimeter of the glass using a utility knife or scraper. (When reusing the glass)

2. Clean and degrease an approx. 50 mm {2.0 in} wide strip along the perimeter of the glass.

3. Inspect the glass for cracks. If it is cracked, chamfer it using sandpaper.

4. Install the spacers, and pins to the glass as shown in the figure.






NOTE:
- When reusing the glass, align it with the alignment mark placed before the glass was removed.

5. Apply glass primer on the glass as shown in the figure then allow it to dry for approx. 30 min.

CAUTION:
- To prevent weakening of the primer adhesion, keep the bonding surface free of dirt, moisture, and grease. Do not touch the surface with your hand.

NOTE:
- Apply primer to the hollowed marks in the ceramic coating.






6. Cut away the old sealant using a utility knife or scraper so that 1-2 mm {0.04-0.07 in} thickness of sealant remains along the perimeter of the frame.






7. Clean and degrease along the perimeter of the bonding area on the body.

8. If the sealant has come off completely in any one place, apply some primer, and allow it to dry for approx. 30 min.

CAUTION:
- To prevent weakening of the primer adhesion, keep the bonding surface free of dirt, moisture, and grease. Do not touch the surface with your hand.

9. Apply body primer on the body as shown in the figure, then allow it to dry for approx. 30 min.

CAUTION:
- To prevent weakening of the primer adhesion, keep the bonding surface free of dirt, moisture, and grease. Do not touch the surface with your hand.

NOTE:
- Apply primer to the hollowed marks in the ceramic coating.






10. Apply sealant to the area of the glass surface as shown in the figure.






11. Install the rear window glass.

12. Verify that the gap at the upper and lower parts of the glass is within the specification shown in the figure, then press along the perimeter of the glass.






13. Connect the filament connector.






14. Install the following parts:
a. Rear wiper arm and blade Rear Wiper Arm And Blade Removal/Installation

b. Rear spoiler Service and Repair

c. Liftgate lower trim

d. Liftgate side trim

e. High-mount brake light Removal and Replacement

f. Liftgate upper trim (See .)

15. Allow the sealant to harden completely. Sealant hardening time: 24 h