Inspection Procedure 18
INSPECTION PROCEDURE 18: Transient, Mass Emission Tailpipe Test Failure.
COMMENT
- The test is failed when the air/fuel ratio is not controlled to the ideal air/fuel ratio. This occurs due to the feedback control by heated oxygen sensor signals, insufficient EGR flow rate, or deteriorated catalyst.
NOTE:
If the three-way catalyst temperature is low when checking the exhaust gas, the three-way catalyst cannot sufficiently clean the emissions. Warm up the engine sufficiently before checking the exhaust, and check immediately.
TROUBLESHOOTING HINTS (The most likely causes for this case:)
- Malfunction of air/fuel ratio control system.
- Malfunction of the EGR system.
- Deteriorated catalyst.
DIAGNOSIS
Required Special Tools:
- MB991958: Scan Tool (M.U.T.-III Sub Assembly)
- MB991824: V.C.I.
- MB991827: USB Cable
- MB991910: Main Harness A
STEP 1. Check the exhaust gas with the engine at normal operating temperature.
Q. Was the exhaust gas checked with engine warmed sufficiently?
YES Go to Step 2.
NO Check it again after enough warm up.
STEP 2. Check the following items.
(1)Check the following items.
1. Check all vacuum hoses and connectors.
2. Check electrical wires and connectors for obvious problems.
Q. Are they normal?
YES Go to Step 3.
NO Repair or replace it. Then confirm that the malfunction symptom is eliminated.
STEP 3. Check the driveability.
Q. Is the driveability normal?
YES Go to Step 4.
NO Refer to Symptom Chart Symptom Chart.
STEP 4. Using scan tool MB991958, read the diagnostic trouble code
(DTC).
CAUTION:
To prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK"
(OFF) position before connecting or disconnecting scan tool MB991958.
(1)Connect scan tool MB991958 to the data link connector.
(2)Turn the ignition switch to the "ON" position.
(3)Read the DTC.
(4)Turn the ignition switch to the "LOCK" (OFF) position.
Q. Is any DTC set?
YES Refer to Diagnostic Trouble Code Chart Multiport Fuel Injection (MFI).
NO Go to Step 5.
STEP 5. Check the ignition timing.
Testing and Inspection.
Q. Is the ignition timing normal?
YES Go to Step 6.
NO Check that the crankshaft position sensor and timing belt cover are in the correct position. Then confirm that the malfunction symptom is eliminated.
STEP 6. Using scan tool MB991958, check data list.
(1)Turn the ignition switch to the "ON" position.
(2)Check the following items in the data list. Refer to Data List Reference Table Data List Reference Table.
3. Item 6: Engine Coolant Temperature Sensor.
4. Item 5: Intake Air Temperature Sensor.
5. Item AC: Heated Oxygen Sensor Bank 1, Sensor 1 (right front)
6. Item AE: Heated Oxygen Sensor Bank 2, Sensor 1 (left front)
7. Item BB: Barometric Pressure Sensor
(3)Turn the ignition switch to the "LOCK" (OFF) position.
Q. Are they operating properly?
YES Go to Step 7.
NO Repair or replace it. Then confirm that the malfunction symptom is eliminated.
STEP 7. Using scan tool MB991958, check data list item AD: Heated oxygen sensor bank 1, sensor 2 (right rear).
(1)Start the engine and run at idle.
(2)Set scan tool MB991958 to the data reading mode for item AD, Heated Oxygen Sensor bank 1, sensor 2 (right rear).
8. Transaxle: 2 nd
9. Drive with wide open throttle
10. Engine: 3,500 r/min
- The output voltages should be between 0.6 and 1.0 volt.
(3)Turn the ignition switch to the "LOCK" (OFF) position.
Q. Is the sensor operating properly?
YES Go to Step 8.
NO Refer to P0137 - Heated Oxygen Sensor Circuit Low Voltage (bank 1, sensor 2) P0137, DTC P0138 - Heated Oxygen Sensor Circuit High Voltage
(bank 1, sensor 2) P0138, DTC P0139 - Heated Oxygen Sensor Circuit Slow Response (bank 1, sensor 2) P0139, DTC P0140 - Heated Oxygen Sensor Circuit No Activity Detected (bank 1, sensor 2) P0140.
STEP 8. Using scan tool MB991958, check data list item AF: Heated oxygen sensor bank 2, sensor 2 (left rear).
(1)Start the engine and run at idle.
(2)Set scan tool MB991958 to the data reading mode for item AF, Heated Oxygen Sensor bank 2, sensor 2 (left rear).
11. Transaxle: 2 nd
12. Drive with wide open throttle
13. Engine: 3,500 r/min
- The output voltage should be between 0.6 and 1.0 volt.
(3)Turn the ignition switch to the "LOCK" (OFF) position.
Q. Is the sensor operating properly?
YES Go to Step 9.
NO Refer to P0157 - Heated Oxygen Sensor Circuit Low Voltage (bank 2, sensor 2) P0157, DTC P0158 - Heated Oxygen Sensor Circuit High Voltage
(bank 2, sensor 2) P0158, DTC P0159 - Heated Oxygen Sensor Circuit Slow Response (bank 2, sensor 2) P0159, DTC P0160 - Heated Oxygen Sensor Circuit No Activity Detected (bank 2, sensor 2) P0160.
STEP 9. Check the EGR system.
Description and Operation.
Q. Is the EGR system normal?
YES Go to Step 10.
NO Repair or replace it. Then confirm that the malfunction symptom is eliminated.
STEP 10. Check the fuel pressure.
Refer to On-vehicle Service - Fuel Pressure Test Testing and Inspection.
Q. Is the fuel pressure normal?
YES Go to Step 11.
NO Repair or replace it. Then confirm that the malfunction symptom is eliminated.
STEP 11. Check the spark plugs.
Procedures.
Q. Are there any abnormalities?
YES Replace the spark plug. Then confirm that the malfunction symptom is eliminated.
NO Go to Step 12.
STEP 12. Check the ignition coil.
(1)Remove the intake manifold.
(2) Testing and Inspection.
Q. Are there any abnormalities?
YES Replace the ignition coil. Then confirm that the malfunction symptom is eliminated.
NO Go to Step 13.
STEP 13. Check the compression pressure.
Testing and Inspection.
Q. Is the compression pressure normal?
YES Go to Step 14.
NO Repair it. Then confirm that the malfunction symptom is eliminated.
STEP 14. Check the positive crankcase ventilation valve.
Crankcase Ventilation System Check.
Q. Is the positive crankcase ventilation valve?
YES Go to Step 15.
NO Repair it. Then confirm that the malfunction symptom is eliminated.
STEP 15. Check the purge control system.
Purge Control System Check.
Q. Is the purge control system normal?
YES Go to Step 16.
NO Repair it. Then confirm that the malfunction symptom is eliminated.
STEP 16. Check the following items.
(1)Check the following items.
14. Check the injectors for fuel leakage.
15. Check if the injectors are clogged.
Q. Are there any abnormalities?
YES Replace it. Then confirm that the malfunction symptom is eliminated. Then confirm that the malfunction symptom is eliminated.
NO Replace the catalytic converter. Then confirm that the malfunction symptom is eliminated.