P0133
P0133 A/F SENSOR 1
Description
The air fuel ratio (A/F) sensor 1 is a planar one-cell limit current sensor. The sensor element of the A/F sensor 1 is composed an electrode layer, which transports ions. It has a heater in the element.
The sensor is capable of precise measurement = 1, but also in the lean and rich range. Together with its control electronics, the sensor outputs a clear, continuous signal throughout a wide range.
The exhaust gas components diffuse through the diffusion layer at the sensor cell. An electrode layer is applied voltage, and this current relative oxygen density in lean. Also this current relative hydrocarbon density in rich.
Therefore, the A/F sensor 1 is able to indicate air fuel ratio by this electrode layer of current. In addition, a heater is integrated in the sensor to ensure the required operating temperature of approximately 800�C (1,472�F).
DTC Logic
DTC DETECTION LOGIC
To judge the malfunction of A/F sensor 1, this diagnosis measures response time of the A/F signal computed by ECM from the A/F sensor 1 signal. The time is compensated by engine operating (speed and load), fuel feedback control constant, and the A/F sensor 1 temperature index. Judgment is based on whether the compensated time (the A/F signal cycling time index) is inordinately long or not.
DTC CONFIRMATION PROCEDURE
1. PRECONDITIONING
If DTC CONFIRMATION PROCEDURE has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.
Do you have CONSULT?
YES- GO TO 2.
NO- GO TO 5.
2. PERFORM DTC CONFIRMATION PROCEDURE-I
With CONSULT
1.Start engine and warm it up to normal operating temperature.
2.Turn ignition switch OFF and wait at least 10 seconds.
3.Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1minute under no load.
4.Let engine idle for 1 minute.
5.Select "A/F SEN1(B1) P1278/P1279" of "A/F SEN1" in "DTC WORK SUPPORT" mode with CONSULT.
6.Touch "START".
Is "COMPLETED" displayed on CONSULT?
YES- GO TO 3
NO- GO TO 4.
3. PERFORM DTC CONFIRMATION PROCEDURE-II
Touch "SELF-DIAG RESULT".
Which is displayed on CONSULT?
OK- INSPECTION END
NG- Go to "Diagnosis Procedure" .
4. PERFORM DTC CONFIRMATION PROCEDURE
1.After perform the following procedure, "TESTING" will be displayed on the CONSULT screen.
-Increase the engine speed up to between 4,000 and 5,000 rpm and maintain that speed for 10 seconds.
-Fully release accelerator pedal and then let engine idle for approximately 10 seconds.
If "TESTING" is not displayed after 10 seconds, refer to "Component Function Check" For Mexico.
2.Wait for approximately 20 seconds at idle under the condition that "TESTING" is displayed on the CONSULT screen.
3.Check that "TESTING" changes to "COMPLETED".
If "TESTING" changed to "OUT OF CONDITION", refer to "Component Function Check" For Mexico.
4.Touch "SELF-DIAG RESULT".
Which is displayed on CONSULT?
OK- INSPECTION END
NG- Go to "Diagnosis Procedure" .
5. CHECK AIR-FUEL RATIO SELF-LEARNING VALUE
With GST
1.Start engine and warm it up to normal operating temperature.
2.Select Service $01 with GST.
3.Calculate the total value of "Short-term fuel trim" and "Long-term fuel trim" indications.
Is the total percentage within ±15%?
YES- GO TO 7.
NO- GO TO 6.
6. DETECT MALFUNCTIONING PART
Check the following.
- Intake air leaks
- Exhaust gas leaks
- Incorrect fuel pressure
- Lack of fuel
- Fuel injector
- Incorrect PCV hose connection
- PCV valve
- Mass air flow sensor
- Repair or replace malfunctioning part.
7. PERFORM DTC CONFIRMATION PROCEDURE
1.Turn ignition switch OFF and wait at least 10 seconds.
2.Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1minute under no load.
3.Let engine idle for 1 minute.
4.Increase the engine speed up to between 4,000 and 5,000 rpm and maintain that speed for 10 seconds.
5.Fully release accelerator pedal and then let engine idle for approximately 1 minute.
6.Check 1st trip DTC detected?.
Is 1st trip DTC detected?
YES- Go to "Diagnosis Procedure" .
NO- INSPECTION END
Diagnosis Procedure
1. CHECK GROUND CONNECTION
1.Turn ignition switch OFF.
2.Check ground connection E21. Refer to Ground Inspection in "Circuit Inspection" Circuit Inspection.
Is the inspection result normal?
YES- GO TO 2.
NO- Repair or replace ground connection.
2. RETIGHTEN A/F SENSOR 1
Loosen and retighten the A/F sensor 1. Refer to "Removal and Installation" Removal And Installation.
- GO TO 3.
3. CHECK EXHAUST GAS LEAK
1.Start engine and run it at idle.
2.Listen for an exhaust gas leak before three way catalyst (manifold).
Is exhaust gas leak detected?
YES- Repair or replace.
NO- GO TO 4.
4. CHECK FOR INTAKE AIR LEAK
Listen for an intake air leak after the mass air flow sensor.
Is intake air leak detected?
YES- Repair or replace.
NO- GO TO 5.
5. CLEAR THE MIXTURE RATIO SELF-LEARNING VALUE
1.Clear the mixture ratio self-learning value. Refer to "MIXTURE RATIO SELF-LEARNING VALUE CLEAR : Special Repair Requirement" For Mexico.
2.Run engine for at least 10 minutes at idle speed.
Is the 1st trip DTC P0171 or P172 detected? Is it difficult to start engine?
YES- Perform trouble diagnosis for DTC P0171 or P0172. Refer to "DTC Logic" Engine Controls or "DTC Logic" Engine Controls.
NO- GO TO 6.
6. CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT
1.Disconnect A/F sensor 1 harness connector.
2.Turn ignition switch ON.
3.Check the voltage between A/F sensor 1 harness connector and ground.
Is the inspection result normal?
YES- GO TO 8.
NO- GO TO 7.
7. DETECT MALFUNCTIONING PART
Check the following.
- Harness connectors E6, F123
- IPDM E/R harness connector E14
- 15 A fuse (No. 63)
- Harness for open or short between A/F sensor 1 and fuse
- Repair or replace harness or connectors.
8. CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.Turn ignition switch OFF.
2.Disconnect ECM harness connector.
3.Check the continuity between A/F sensor 1 harness connector and ECM harness connector.
4.Check the continuity between A/F sensor 1 harness connector or ECM harness connector and ground.
5.Also check harness for short to power.
Is the inspection result normal?
YES- GO TO 9.
NO- Repair open circuit or short to ground or short to power in harness or connectors.
9. CHECK AIR FUEL RATIO (A/F) SENSOR 1 HEATER
Refer to "Component Inspection" Engine Controls.
Is the inspection result normal?
YES- GO TO 10.
NO- GO TO 13.
10. CHECK MASS AIR FLOW SENSOR
Check mass air flow sensor.
Refer to "Component Inspection" Engine Controls.
Is the inspection result normal?
YES- GO TO 11.
NO- Replace mass air flow sensor. Refer to "Removal and Installation" Removal And Installation.
11. CHECK PCV VALVE
Refer to "Component Inspection" For Mexico.
Is the inspection result normal?
YES- GO TO 12.
NO- Repair or replace PCV valve. Refer to "Component Parts Location" Engine Control System For Mexico.
12. CHECK INTERMITTENT INCIDENT
Perform "Intermittent Incident" Intermittent Incident.
Is the inspection result normal?
YES- GO TO 13.
NO- Repair or replace.
13. REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace air fuel ratio (A/F) sensor 1. Refer to "Exploded View" Exploded View.
CAUTION:
- Discard any A/F sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard surface such as a concrete floor; use a new one.
- Before installing new A/F sensor, clean exhaust system threads using oxygen sensor thread cleaner
[commercial service tool (J-43897-18 or J-43897-12)] and approved anti-seize lubricant (commercial service tool).
- INSPECTION END