Operation CHARM: Car repair manuals for everyone.
Home >> Nissan-Datsun Truck >> 2013 >> Rogue 4WD L4-2.5L (QR25DE) >> Repair and Diagnosis >> Relays and Modules >> Relays and Modules - Powertrain Management >> Relays and Modules - Computers and Control Systems >> Engine Control Module >> Testing and Inspection >> Basic Inspection

Basic Inspection




INSPECTION AND ADJUSTMENT

BASIC INSPECTION : Special Repair Requirement


1. INSPECTION START

1.Check service records for any recent repairs that may indicate a related malfunction, or a current need for scheduled maintenance.





2.Open engine hood and check the following:
-Harness connectors for improper connections
-Wiring harness for improper connections, pinches and cut
-Vacuum hoses for splits, kinks and improper connections
-Hoses and ducts for leakage
-Air cleaner clogging
-Gasket
3.Check that electrical or mechanical loads are not applied.
-Headlamp switch is OFF.
-Air conditioner switch is OFF.
-Rear window defogger switch is OFF.
-Steering wheel is in the straight-ahead position, etc.





4.Start engine and warm it up until engine coolant temperature indicator points to the middle of gauge.
Check that engine stays below 1,000 rpm.





5.Run engine at approximately 2,000 rpm for approximately 2 minutes under no load.
6.Check that no DTC is displayed with CONSULT or GST.
Are any DTCs detected?
YES- GO TO 2.
NO- GO TO 3.

2. REPAIR OR REPLACE

Repair or replace components as necessary according to corresponding Diagnosis Procedure.
- GO TO 3

3. CHECK IDLE SPEED

1.Run engine at approximately 2,000 rpm for approximately 2 minutes under no load.





2.Rev engine (2,000 to 3,000 rpm) two or three times under no load, then run engine at idle speed for approximately 1 minute.
3.Check idle speed.
For procedure, refer to "IDLE SPEED : Special Repair
Requirement".
For specification, refer to "Idle Speed" Except For Mexico.
Is the inspection result normal?
YES- GO TO 10.
NO- GO TO 4.

4. PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING

1.Stop engine.
2.Perform "ACCELERATOR PEDAL RELEASED POSITION LEARNING : Special Repair Requirement" Except For Mexico.
- GO TO 5.

5. PERFORM THROTTLE VALVE CLOSED POSITION LEARNING

Perform "THROTTLE VALVE CLOSED POSITION LEARNING : Special Repair Requirement" Except For Mexico.
- GO TO 6.

6. PERFORM IDLE AIR VOLUME LEARNING

Perform "IDLE AIR VOLUME LEARNING : Special Repair Requirement" Except For Mexico.
Is Idle Air Volume Learning carried out successfully?
YES- GO TO 7.
NO- Follow the instruction of Idle Air Volume Learning. Then GO TO 4.

7. CHECK IDLE SPEED AGAIN

1.Start engine and warm it up to normal operating temperature.
2.Check idle speed.
For procedure, refer to "IDLE SPEED : Special Repair Requirement" Except For Mexico.
For specification, refer to "Idle Speed" Except For Mexico.
Is the inspection result normal?
YES- GO TO 10.
NO- GO TO 8.

8. DETECT MALFUNCTIONING PART

Check the Following.
- Check camshaft position sensor (PHASE) and circuit. Refer to "DTC Logic" CMP Sensor (PHASE).
- Check crankshaft position sensor (POS) and circuit. Refer to "DTC Logic" CKP Sensor (POS).
Is the inspection result normal?
YES- GO TO 9.
NO- Repair or replace. Then GO TO 4.

9. CHECK ECM FUNCTION

1.Substitute another with a non-malfunctioning ECM to check ECM function. (ECM may be the cause of an incident, although this is rare.)
NOTE:
Use the specified bolts described in parts information certainly when installing the ECM, or violates the
Canada law.
2.Perform initialization of NVIS (NATS) system and registration of all NVIS (NATS) ignition key IDs. Refer to
"ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement" Except For Mexico.
- GO TO 4.

10. CHECK IGNITION TIMING

1.Run engine at idle.
2.Check ignition timing with a timing light.
For procedure, refer to "IGNITION TIMING : Special Repair Requirement" Except For Mexico.
For specification, refer to "Ignition Timing" Except For Mexico.
Is the inspection result normal?
YES- GO TO 19.
NO- GO TO 11.

11. PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING

1.Stop engine.
2.Perform "ACCELERATOR PEDAL RELEASED POSITION LEARNING : Special Repair Requirement" Except For Mexico.
- GO TO 12.

12. PERFORM THROTTLE VALVE CLOSED POSITION LEARNING

Perform "THROTTLE VALVE CLOSED POSITION LEARNING : Special Repair Requirement" Except For Mexico.
- GO TO 13.

13. PERFORM IDLE AIR VOLUME LEARNING

Perform "IDLE AIR VOLUME LEARNING : Special Repair Requirement" Except For Mexico.
Is Idle Air Volume Learning carried out successfully?
YES- GO TO 14.
NO- Follow the instruction of Idle Air Volume Learning. Then GO TO 4.

14. CHECK IDLE SPEED AGAIN

1.Start engine and warm it up to normal operating temperature.
2.Check idle speed.
For procedure, refer to "IDLE SPEED : Special Repair Requirement" Except For Mexico.
For specification, refer to "Idle Speed" Except For Mexico.
Is the inspection result normal?
YES- GO TO 15.
NO- GO TO 17.

15. CHECK IGNITION TIMING AGAIN

1.Run engine at idle.
2.Check ignition timing with a timing light.
For procedure, refer to "IGNITION TIMING : Special Repair Requirement" Except For Mexico.
For specification, refer to "Ignition Timing" Except For Mexico.
Is the inspection result normal?
YES- GO TO 19.
NO- GO TO 16.

16. CHECK TIMING CHAIN INSTALLATION

Check timing chain installation. Refer to "Removal and Installation" Removal And Installation.
Is the inspection result normal?
YES- GO TO 17.
NO- Repair the timing chain installation. Refer to "Removal and Installation" Removal And Installation. Then GO TO 4.

17. DETECT MALFUNCTIONING PART

Check the following.
- Check camshaft position sensor (PHASE) and circuit. Refer to "DTC Logic" CMP Sensor (PHASE).
- Check crankshaft position sensor (POS) and circuit. Refer to "DTC Logic" CKP Sensor (POS).
Is the inspection result normal?
YES- GO TO 18.
NO- Repair or replace. Then GO TO 4.

18. CHECK ECM FUNCTION

1.Substitute with a non-malfunctioning ECM to check ECM function. (ECM may be the cause of a incident, although this is rare.)
NOTE:
Use the specified bolts described in parts information certainly when installing the ECM, or violates the
Canada law.
2.Perform initialization of NVIS (NATS) system and registration of all NVIS (NATS) ignition key IDs. Refer to
"ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement" Except For Mexico.
- GO TO 4.

19. INSPECTION END

If ECM is replaced during this BASIC INSPECTION procedure, go to , "ADDITIONAL SERVICE WHEN
REPLACING CONTROL UNIT : Special Repair Requirement".
- INSPECTION END
pro multis · About Operation CHARM