DTC 1308

NOTE: Since this diagnosis does not meet P1900 of SAE J2012, it is indicated only by CONSULT.




SYSTEM DESCRIPTION

Cooling Fan Control
The ECM controls the cooling fan corresponding to the vehicle speed, engine coolant temperature, and air conditioner ON signal. The control system has 3-step control [HIGH/LOW/OFF] on A/T models and 2-step control [HIGH/OFF] on M/T models.

OPERATION




For A/T models




For M/T models




CONSULT REFERENCE VALUE IN DATA MONITOR MODE







ECM TERMINALS AND REFERENCE VALUE
Specification data are reference values and are measured between each terminal and (43) (ECCS ground).

ON BOARD DIAGNOSIS LOGIC
If the cooling fan or another component in the cooling system malfunctions, engine coolant temperature will rise.
When the engine coolant temperature reaches an abnormally high temperature condition, a malfunction is indicated.

CAUTION:
When a malfunction is indicated, be sure to replace the coolant following the procedure "Changing Engine Coolant", "ENGINE MAINTENANCE". Also, replace the engine oil.
a. Fill radiator with coolant up to specified level with a filling speed of 2 liters per minute. Be sure to use coolant with the proper mixture ratio. Refer to "Anti-freeze Coolant Mixture Ratio", "RECOMMENDED FLUIDS AND LUBRICANTS".
b. After refilling coolant, run engine to ensure that no water-flow noise is emitted.

OVERALL FUNCTION CHECK
Use this procedure to check the overall function of the cooling fan. During this check, a DTC might not be confirmed.

WARNING:
Never remove the radiator cap when the engine is hot. Serious burns could be caused by high pressure fluid escaping from the radiator.
Wrap a thick cloth around cap. Carefully remove the cap by turning it a quarter turn to allow built-up pressure to escape. Then turn the cap all the way off.

With Consult




(1) Check the coolant level in the reservoir tank and radiator. Allow engine to cool before checking coolant level. If the coolant level in the reservoir tank and/or radiator is below the proper range, skip the following steps and go to "DIAGNOSTIC PROCEDURE".
(2) Confirm whether customer filled the coolant or not. If customer filled the coolant, skip the following steps and go to "DIAGNOSTIC PROCEDURE".
(3) Turn ignition switch "ON".




(4) Perform "COOLING FAN" in "ACTIVE TEST" mode with CONSULT

OR

Without Consult
(3) Start engine. Be careful not to overheat engine.
(4) Turn air conditioner switch "ON".
(5) Turn blower fan switch "ON".




(6) Make sure that cooling fan operates.
(7) Turn ignition switch "OFF".
(8) Turn air conditioner switch and blower fan switch "OFF".
(9) Disconnect engine coolant temperature sensor harness connector.




(10) Connect 150 Ohms resistor to engine coolant temperature sensor harness connector.
(11) Restart engine and make sure that cooling fan operates. Be careful not to overheat engine.







DIAGNOSTIC PROCEDURE







DIAGNOSTIC PROCEDURE A










DIAGNOSTIC PROCEDURE B

Perform FINAL CHECK
by the following procedure after repair is completed.
1. Warm up engine. Run the vehicle for at least 20 minutes. Pay attention to engine coolant temperature gauge on the instrument panel. If the reading shows an abnormally high temperature, another part may be malfunctioning.
2. Stop vehicle and let engine idle. Check the intake and exhaust systems for leaks by listening for noise or visually inspecting the components.
3. Allow engine to cool and visually check for oil and coolant leaks. Then, perform "OVERALL FUNCTION CHECK".




MAIN 12 CAUSES OF OVERHEATING

COMPONENT INSPECTION

Cooling Fan Relays -1, -2 and -3
Check continuity between terminals (3) and (5).




Conditions / Continuity
12V direct current supply between terminals (1) and (2) / Yes
No current supply / No

If NG, replace relay.

Cooling Fan Motors -1 and -2
1. Disconnect cooling fan motor harness connectors.







2. Supply cooling fan motor terminals with battery voltage and check operation.




Cooling fan motor should operate.
If NG, replace cooling fan motor.