Vehicle Security (Theft Warning) System
VEHICLE SECURITY (THEFT WARNING) SYSTEMSystem Description
DESCRIPTION
1. Operation Flow
2. Setting The Vehicle Security System
Initial condition
1. Ignition switch is in OFF position.
Disarmed phase
When the vehicle security system is in the disarmed phase, the security indicator lamp blinks every 2.6 seconds.
Pre-armed phase and armed phase
When the following operation 1 or 2 is performed, the vehicle security system turns into the "pre-armed" phase. (The security indicator lamp illuminates.)
1. Smart entrance control unit receives LOCK signal from key cylinder switch or keyfob after hood, trunk lid and all doors are closed.
2. Trunk lid and all doors are closed after front doors are locked by key, lock/unlock switch or keyfob.
After about 30 seconds, the system automatically shifts into the "armed" phase (the system is set). (The security indicator lamp blinks every 2.6 seconds.)
3. Canceling The Set Vehicle Security System
When the following 1 or 2 operation is performed, the armed phase is canceled.
1. Unlock the doors with the key or keyfob.
2. Open the trunk lid with the key or keyfob.
4. Activating The Alarm Operation of The Vehicle Security System
Make sure the system is in the armed phase. (The security indicator lamp blinks every 2.6 seconds.)
When the following operation 1 or 2 is performed, the system sounds the horns and flashes the headlamps for about 50 seconds.
1. Trunk lid or any door is opened during armed phase.
2. Disconnecting and connecting the battery connector before canceling armed phase.
POWER SUPPLY AND GROUND
Power is supplied at all times:
- through 10 A fuse [No. 12, located in the fuse block (J/B)]
- to security indicator lamp terminal 1 and
- to key switch terminal 2.
Power is supplied at all times:
- through 10 A fuse (No. 37, located in the fuse and fusible link box)
- to smart entrance control unit terminal 10.
With the ignition switch in the ON or START position, power is supplied:
- through 10 A fuse [No. 10, located in the fuse block (J/B)]
- to smart entrance control unit terminal 33.
With the ignition switch in the ACC or ON position, power is supplied:
- through 10 A fuse [No. 1, located in the fuse block (J/B)]
- to smart entrance control unit terminal 21.
Ground is supplied:
- to smart entrance control unit terminal 16
- through body grounds M28 and M54.
INITIAL CONDITION TO ACTIVATE THE SYSTEM
The operation of the vehicle security system is controlled by the doors, hood and trunk lid.
Pattern A
To activate the vehicle security system, the smart entrance control unit must receive signals indicating the doors, hood and trunk lid are closed.
When a door is open, smart entrance control unit terminal 28 or 29 receives a ground signal from each door switch.
When the trunk lid is open, smart entrance control unit terminal 38 receives a ground signal:
- from terminal + of the trunk room lamp switch
- to terminal - of the trunk room lamp switch
- through body grounds B13 and B19.
When smart entrance control unit receives LOCK signal from key cylinder switch or keyfob and none of the described conditions exist, the vehicle security system will automatically shift to armed mode.
Pattern B
To activate the vehicle security system, the smart entrance control unit must receive signal indicating any door (including trunk lid) is opened.
When the front doors are locked with key, lock/unlock switch or keyfob and then all doors are closed, the vehicle security system will automatically shift to armed mode.
VEHICLE SECURITY SYSTEM ACTIVATION
Pattern A
With all doors closed (including trunk lid), if the key is used to lock doors, smart entrance control unit terminal 41 receives a ground signal:
- from terminal L of the front door key cylinder switch LH
- to terminal E of the front door key cylinder switch LH
- through body grounds M28 and M54.
If this signal, or lock signal from keyfob is received by the smart entrance control unit, the vehicle security system will activate automatically.
NOTE: Vehicle security system can be set even though all doors are not locked.
Pattern B
With any door open, if lock/unlock switch is used to lock doors, smart entrance control unit terminal 23 receives a ground signal:
- from terminal 14 of main power window and door lock/unlock switch
- to terminal 3 of main power window and door lock/unlock switch, or
- from terminal 1 of door lock/unlock switch RH
- to terminal 5 of door lock/unlock switch RH
- through body grounds M28 and M54.
With any door open, if the key is used to lock doors, smart entrance control unit terminal 41 receives a ground signal:
- from terminal L of the front door key cylinder switch LH
- to terminal E of the front door key cylinder switch LH
- through body grounds M28 and M54.
If these signals and lock signal from keyfob are received by the smart entrance control unit and ground signals of terminals 36 and 37 are interrupted (both front doors locked), the vehicle security system will activate automatically.
NOTE: Vehicle security system can be set even though the rear door is not locked.
Once the vehicle security system has been activated, smart entrance control unit terminal 31 supplies ground to terminal 2 of the security indicator lamp.
The security indicator lamp will illuminate for approximately 30 seconds and then blink every 2.6 seconds. Now the vehicle security system is in armed phase.
VEHICLE SECURITY SYSTEM ALARM OPERATION
The vehicle security system is triggered by:
- opening a door
- opening the trunk lid
- detection of battery disconnect and connect.
Once the vehicle security system is in armed phase, if the smart entrance control unit receives a ground signal at terminal 28 or 29 (door switch) or 38 (trunk room lamp switch), the vehicle security system will be triggered.
The headlamps flash and the horn sounds intermittently.
Power is supplied at all times:
- through 15 A fuse (No. 39, located in fuse and fusible link box)
- to vehicle security lamp relay terminal 3,
- through 15 A fuse (No. 40, located in fuse and fusible link box)
- to vehicle security lamp relay terminal 6,
- through 10 A fuse (No, 35 located in fuse and fusible link box)
- to vehicle security lamp relay terminal 1
- through 10 A fuse (No. 33, located in fuse and fusible link box)
- to horn relay terminals 1 and 5.
When the vehicle security system is triggered, ground is supplied intermittently:
- from smart entrance control unit terminal 4
- to horn relay terminal 2 and
- to vehicle security lamp relay terminal 2.
The headlamps flash and the horn sounds intermittently.
The alarm automatically turns off after about 50 seconds but will reactivate if the vehicle is tampered with again.
VEHICLE SECURITY SYSTEM DEACTIVATION
To deactivate the vehicle security system, a door or trunk lid must be unlocked with the key or keyfob.
When the key is used to unlock the door, smart entrance control unit terminal 30 receives a ground signal:
- from terminal U of front door key cylinder switch LH
- to terminal E of front door key cylinder switch LH
- through body grounds M28 and M54.
When the key is used to open the trunk lid, smart entrance control unit terminal 42 receives a ground signal:
- from terminal + of the trunk lid key cylinder switch (unlock switch)
- to terminal - of the trunk lid key cylinder switch (unlock switch)
- through body grounds B13 and B19.
When the smart entrance control unit receives either one of these signals or unlock signal from keyfob, the vehicle security system is deactivated. (Disarmed phase)
PANIC ALARM OPERATION
When the remote keyless entry system (panic alarm) is triggered, ground is supplied intermittently:
- from smart entrance control unit terminal 4
- to vehicle security lamp relay terminal 2 and
- to horn relay terminal 2.
The headlamp flashes and the horn sounds intermittently.
The alarm automatically turns off after 25 seconds or when smart entrance control unit receives any signal from keyfob.