P1760

Description

The overrun clutch solenoid valve is activated by the TCM in response to signals sent from the transmission range switch, overdrive control switch, vehicle speed and ECM (throttle opening). The overrun clutch operation will then be controlled.


CONSULT Reference Value in Data Monitor Mode








On Board Diagnosis Logic

- This is an OBD-II self-diagnostic item.
- Diagnostic trouble code "P1760 OVER CLUTCH SOLENOID" with CONSULT or 6th judgement flicker without CONSULT is detected when TCM detects an improper voltage drop when it tries to operate solenoid valve.


Possible Cause

- Harness or connector (The solenoid circuit is open or shorted.)
- Overrun clutch solenoid valve


DTC Confirmation Procedure


CAUTION:
- Always drive vehicle at a safe speed.
- If performing this "DTC Confirmation Procedure" again, always turn ignition switch OFF and wait at least 10 seconds before continuing.
After the repair, perform the following procedure to confirm the malfunction is eliminated.

WITH CONSULT

1.Turn ignition switch ON and select "DATA MONITOR" mode for "TRANSMISSION" with CONSULT.
2.Touch "START".
3.Start engine.
4.Accelerate vehicle to a speed of more than 10 km/h (6 MPH) with "D" position (OD ON).
5.Release accelerator pedal completely with "D" position (OD OFF).
6.If the check result is NG, go to .

WITH GST

Follow the procedure "WITH CONSULT".

WITHOUT CONSULT

1.Start engine.
2.Drive vehicle under the following conditions:
Selector lever position: "D" position (OD ON)
Vehicle speed: Higher than 10 km/h (6 MPH)

3.Perform self-diagnosis. Automatic Transmission .
4.If the check result is NG, go to .


Wiring Diagram - AT - OVRCSV







TCM TERMINALS AND REFERENCE VALUES

Automatic Transmission.


Diagnosis Procedure


1. CHECK INPUT SIGNAL

With CONSULT
1.Start engine.
2.Select "MAIN SIGNALS" in "DATA MONITOR" mode for "TRANSMISSION" with CONSULT.
3.Read out the value of "OVERRUN/C S/V" while driving.
Check the value changes according to driving speed.





Without CONSULT
1.Start engine.





2.Check voltage between TCM connector terminal and ground.





OK or NG
OK- GO TO 5.
NG- GO TO 2.

2. CHECK OVERRUN CLUTCH SOLENOID VALVE CIRCUIT

1.Turn ignition switch OFF.
2.Disconnect TCM connector.





3.Check resistance between TCM connector terminal and ground.





OK or NG
OK - GO TO 5.
NG- GO TO 3.

3. CHECK HARNESS BETWEEN TCM AND TERMINAL CORD ASSEMBLY HARNESS CONNECTOR

1.Turn ignition switch OFF.
2.Disconnect terminal cord assembly harness connector and TCM connector.





3.Check continuity between terminal cord assembly harness connector terminal and TCM connector terminal.





4.If OK, check harness for short to ground and short to power.
5.If OK, check continuity between ground and transaxle assembly.
6.Reinstall any part removed.
OK or NG
OK- GO TO 4.
NG- Repair open circuit or short to ground or short to power in harness or connectors.

4. CHECK VALVE RESISTANCE

1.Turn ignition switch OFF.
2.Disconnect terminal cord assembly connector in engine room.





3.Check resistance between terminal cord assembly harness connector terminal and ground.





OK or NG
OK- GO TO 5.
NG- Repair or replace damaged parts.

5. CHECK DTC

Perform .
OK or NG
OK-INSPECTION END
NG- GO TO 6.

6. CHECK TCM

1.Check TCM input/output signal. Automatic Transmission.
2.If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK-INSPECTION END
NG- Repair or replace damaged parts.


Component Inspection


OVERRUN CLUTCH SOLENOID VALVE

- For removal, Service and Repair.
Resistance Check





- Check resistance between terminal and ground.





Operation Check





- Check solenoid valve by listening for its operating sound while applying battery voltage to the terminal and ground.