Operation CHARM: Car repair manuals for everyone.

P0443




P0443 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE

DTC Logic


DTC DETECTION LOGIC







DTC CONFIRMATION PROCEDURE


1. PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
1.Turn ignition switch OFF and wait at least 10 seconds.
2.Turn ignition switch ON.
3.Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:
Always perform test at a temperature of 5�C (41�F) or more.
Do you have CONSULT
YES- GO TO 2.
NO- GO TO 3.

2. PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT
1.Start engine and warm it up to normal operating temperature.
2.Turn ignition switch OFF and wait at least 10 seconds.
3.Turn ignition switch ON.
4.Turn ignition switch OFF and wait at least 10 seconds.
5.Turn ignition switch ON.
6.Select "PURG VOL CN/V P1444" of "EVAPORATIVE SYSTEM" in "DTC WORK SUPPORT" mode with
CONSULT.
7.Touch "START".
8.Start engine and let it idle until "TESTING" on CONSULT changes to "COMPLETED". (It will take approximately 10 seconds.)
If "TESTING" is not displayed after 5 minutes, retry from step 2.
9.Touch "SELF-DIAG RESULTS".
Which is displayed on CONSULT screen?
OK- INSPECTION END
NG- Proceed to "Diagnosis Procedure" .

3. PERFORM DTC CONFIRMATION PROCEDURE

With GST
1.Start engine and warm it up to normal operating temperature.
2.Turn ignition switch OFF and wait at least 10 seconds.
3.Turn ignition switch ON.
4.Turn ignition switch OFF and wait at least 10 seconds.
5.Start engine and let it idle for at least 20 seconds.
6.Check 1st trip DTC.
Is 1st trip DTC displayed?
YES- Proceed to "Diagnosis Procedure" .
NO- INSPECTION END


Diagnosis Procedure


1. CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE POWER SUPPLY

1.Turn ignition switch OFF.
2.Disconnect EVAP canister purge volume control solenoid valve harness connector.
3.Turn ignition switch ON.
4.Check the voltage between EVAP canister purge volume control solenoid valve harness connector and ground.





Is the inspection result normal?
YES- GO TO 2.
NO- Perform the trouble diagnosis for power supply circuit.

2. CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OUTPUT SIGNAL CIRCUIT

1.Turn ignition switch OFF.
2.Disconnect ECM harness connector.
3.Check the continuity between EVAP canister purge volume control solenoid valve harness connector and
ECM harness connector.





4.Also check harness for short to ground and short to power.
Is the inspection result normal?
YES- GO TO 3.
NO- Repair open circuit, short to ground or short to power in harness or connectors.

3. CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR CONNECTOR

1.Disconnect EVAP control system pressure sensor harness connector.
2.Check that water is not inside connectors.
Is the inspection result normal?
YES- GO TO 4.
NO- Replace EVAP control system pressure sensor. Refer to "Removal and Installation" Removal And Installation.

4. CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR

Check EVAP control system pressure sensor. Refer to "Component Inspection" P0451.
Is the inspection result normal?
YES-1- With CONSULT: GO TO 5.
YES-2- Without CONSULT: GO TO 6.
NO- Replace EVAP control system pressure sensor. Refer to "Removal and Installation" Removal And Installation.

5. CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE

With CONSULT
1.Turn ignition switch OFF.
2.Reconnect harness connectors disconnected.
3.Start engine.
4.Perform "PURG VOL C/V" in "ACTIVE TEST" mode with CONSULT. Check that engine speed varies according to the valve opening.
Does engine speed vary according to the valve opening?
YES- GO TO 7.
NO- GO TO 6.

6. CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE

Check EVAP canister purge volume control solenoid valve. Refer to "Component Inspection" .
Is the inspection result normal?
YES- GO TO 7.
NO- Replace EVAP canister purge volume control solenoid valve. Refer to "ENGINE CONTROL SYSTEM : Component Parts Location" Locations.

7. CHECK RUBBER TUBE FOR CLOGGING

1.Disconnect rubber tube connected to EVAP canister vent control valve.
2.Check the rubber tube for clogging.
Is the inspection result normal?
YES- GO TO 8.
NO- Clean the rubber tube using an air blower.

8. CHECK EVAP CANISTER VENT CONTROL VALVE

Check EVAP canister vent control valve. Refer to "Component Inspection" P0447.
Is the inspection result normal?
YES- GO TO 9.
NO- Replace EVAP canister vent control valve. Refer to "Removal and Installation" Removal And Installation.

9. CHECK IF EVAP CANISTER IS SATURATED WITH WATER






Remove EVAP canister with EVAP canister vent control valve and
EVAP control system pressure sensor attached. Refer to "Exploded View" Exploded View.
Does water drain from the EVAP canister?
YES- GO TO 10.
NO- Check intermittent incident. Refer to "Intermittent Incident" Intermittent Incident.

10. CHECK EVAP CANISTER

Weigh the EVAP canister with the EVAP canister vent control valve and EVAP control system pressure sensor attached.
The weight should be less than 2.1 kg (4.6 lb).
Is the inspection result normal?
YES- Check intermittent incident. Refer to "Intermittent Incident" Intermittent Incident.
NO- GO TO 11.

11. DETECT MALFUNCTIONING PART

Check the following.
- EVAP canister for damage
- EVAP hose between EVAP canister and vehicle frame for clogging or poor connection
- Repair hose or replace EVAP canister. Refer to "Exploded View" Exploded View.


Component Inspection


1. CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE

With CONSULT
1.Turn ignition switch OFF.
2.Reconnect all harness connectors disconnected.
3.Disconnect EVAP purge hoses connected to EVAP canister purge volume control solenoid valve.
4.Turn ignition switch ON.
5.Select "PURG VOL C/V" in "ACTIVE TEST" mode with CONSULT.





6.Touch "Qd" and "Qu" on CONSULT screen to adjust "PURG
VOL C/V" opening and check air passage continuity of EVAP
canister purge volume control solenoid valve under the following conditions.





Without CONSULT
1.Turn ignition switch OFF.
2.Disconnect EVAP canister purge volume control solenoid valve harness connector.
3.Disconnect EVAP purge hoses connected to EVAP canister purge volume control solenoid valve.





4.Check air passage continuity of EVAP canister purge volume control solenoid valve under the following conditions.





Is the inspection result normal?
YES- INSPECTION END
NO- Replace EVAP canister purge volume control solenoid valve. Refer to "ENGINE CONTROL SYSTEM : Component Parts Location" Locations.