Operation CHARM: Car repair manuals for everyone.
Home >> Nissan-Datsun >> 2013 >> Altima Sedan V6-3.5L (VQ35DE) >> Repair and Diagnosis >> A L L Diagnostic Trouble Codes ( DTC ) >> Testing and Inspection >> P Code Charts >> P0705 >> CVT RE0F10E

CVT RE0F10E




P0705 TRANSMISSION RANGE SENSOR A

DTC Logic


DTC DETECTION LOGIC







DTC CONFIRMATION PROCEDURE


1. PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.
- GO TO 2.

2. CHECK DTC DETECTION

1.Turn ignition switch ON.
2.Shift the selector lever through entire positions from "P" to "DS". (Hold the selector lever at each position for 5 seconds or more.)
3.Check the first trip DTC.
Is "P0705" detected?
YES- Go to "Diagnosis Procedure" .
NO- INSPECTION END


Diagnosis Procedure


1. CHECK TCM INPUT SIGNALS

With CONSULT
1.Turn ignition switch ON.
2.Select "Data Monitor" in "TRANSMISSION".
3.Select "D POSITION SW", "N POSITION SW", "R POSITION SW", "P POSITION SW" and "DS RANGE
SW".
4.Shift the selector lever through entire positions from "P" to "DS" and check ON/OFF of each monitor item.





Without CONSULT
1.Turn ignition switch OFF.
2.Disconnect TCM connector.
3.Turn ignition switch ON.
4.Shift the selector lever from "P" to "DS" and check voltage between TCM harness connector terminals and ground.





Is the inspection result normal?
YES - Check intermittent incident. Refer to "Intermittent Incident" Intermittent Incident.
NO-1 ["D POSITION SW" is "ON" when selector is not in "D" position. (Or connector terminal 4 is at power voltage.)]-GO TO 2.
NO-2 ["N POSITION SW" is "ON" when selector is not in "N" position. (Or connector terminal 5 is at power voltage.)]-GO TO 4.
NO-3 ["R POSITION SW" is "ON" when selector is not in "R" position. (Or connector terminal 6 is at power voltage.)]-GO TO 6.
NO-4 ["P POSITION SW" is "ON" when selector is not in "P" position. (Or connector terminal 7 is at power voltage.)]-GO TO 8.
NO-5 ["DS POSITION SW" is "ON" when selector is not in "DS" position. (Or connector terminal 2 is at power voltage.)]-GO TO 10.

2. CHECK D POSITION SW CIRCUIT (PART 1)

1.Turn ignition switch OFF.
2.Disconnect TCM connector.
3.Check continuity between TCM harness connector terminals.





Is the inspection result normal?
YES- GO TO 3.
NO- Repair or replace malfunctioning parts.

3. CHECK D POSITION SW CIRCUIT (PART 2)

1.Disconnect transmission range switch connector.
2.Turn ignition switch ON.
3.Check voltage between TCM harness connector terminal and ground.





Is the inspection result normal?
YES- GO TO 12.
NO- Repair or replace malfunctioning parts.

4. CHECK N POSITION SW CIRCUIT (PART 1)

1.Turn ignition switch OFF.
2.Disconnect TCM connector.
3.Check continuity between TCM harness connector terminals.





Is the inspection result normal?
YES- GO TO 5.
NO- Repair or replace malfunctioning parts.

5. CHECK N POSITION SW CIRCUIT (PART 2)

1.Disconnect transmission range switch connector.
2.Turn ignition switch ON.
3.Check voltage between TCM harness connector terminal and ground.





Is the inspection result normal?
YES- GO TO 12.
NO- Repair or replace malfunctioning parts.

6. CHECK P POSITION SW CIRCUIT (PART 1)

1.Turn ignition switch OFF.
2.Disconnect TCM connector.
3.Check continuity between TCM harness connector terminals.





Is the inspection result normal?
YES- GO TO 7.
NO- Repair or replace malfunctioning parts.

7. CHECK P POSITION SW CIRCUIT (PART 2)

1.Disconnect transmission range switch connector.
2.Turn ignition switch ON.
3.Check voltage between TCM harness connector terminal and ground.





Is the inspection result normal?
YES- GO TO 12.
NO- Repair or replace malfunctioning parts.

8. CHECK R POSITION SW CIRCUIT (PART1)

1.Turn ignition switch OFF.
2.Disconnect TCM connector.
3.Check continuity between TCM harness connector terminals.





Is the inspection result normal?
YES- GO TO 9.
NO- Repair or replace malfunctioning parts.

9. CHECK R POSITION SW CIRCUIT (PART 2)

1.Disconnect transmission range switch connector.
2.Turn ignition switch ON.
3.Check voltage between TCM harness connector terminal and ground.





Is the inspection result normal?
YES- GO TO 12.
NO- Repair or replace malfunctioning parts.

10. CHECK DS POSITION SWITCH CIRCUIT (PART 1)

1.Turn ignition switch OFF.
2.Disconnect TCM connector.
3.Check continuity between TCM harness connector terminals.





Is the inspection result normal?
YES- GO TO 11.
NO- Repair or replace malfunctioning parts.

11. CHECK DS POSITION SWITCH CIRCUIT (PART 2)

1.Disconnect transmission range switch connector.
2.Turn ignition switch ON.
3.Check voltage between TCM harness connector terminal and ground.





Is the inspection result normal?
YES- GO TO 12.
NO- Repair or replace malfunctioning parts.

12. CHECK TRANSMISSION RANGE SWITCH

Check transmission range switch. Refer to "Component Inspection" .
Is the check result normal?
YES- Check intermittent incident. Refer to "Intermittent Incident" Intermittent Incident.
NO- Repair or replace malfunctioning parts.


Component Inspection


1. CHECK TRANSMISSION RANGE SWITCH

Check continuity between transmission range switch connector terminals.





Is the inspection result normal?
YES- INSPECTION END
NO- There is a malfunction of transmission range switch. Replace transaxle assembly. Refer to TM408, "Removal and Installation".
pro multis · About Operation CHARM