P0711
DTC P0711, P0712, or P0713
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Initial Inspection and Diagnostic Overview) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Initial Inspection and Diagnostic Overview) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Initial Inspection and Diagnostic Overview) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0711
- Transmission Fluid Temperature (TFT) Sensor Performance
DTC P0712
- Transmission Fluid Temperature (TFT) Sensor Circuit Low Voltage
DTC P0713
- Transmission Fluid Temperature (TFT) Sensor Circuit High Voltage
Diagnostic Fault Information
Circuit/System Description
The transmission fluid temperature (TFT) sensor input/output circuitry consists of an oil temperature sensor signal (-) (OTG), and an oil temperature sensor signal (+) (OT). The sensor converts the transmission oil temperature inside the transmission into an electrical signal and transmits it to the transmission control module (TCM).
Conditions for Running the DTC
P0711
* There is no transmission range switch DTC P0705.
* The transmission is not in Emergency Mode.
* The transmission oil temperature is less than 20°C (68°F) at initialization.
* The transmission oil temperature is between -30 to +150°C (-22 to +302°F).
* The transmission range is D, 3, 2, or 1.
* The vehicle speed has been greater than 40 km/h (24 mph) at least once.
P0712
* The engine is running for greater than 2 seconds.
* The transmission is not in Emergency Mode.
P0713
* There is no engine coolant temperature DTC P1258.
* The transmission is not in Emergency Mode.
* The drive time is greater than 600 seconds (10 minutes).
Conditions for Setting the DTC
P0711
The TCM detects that the transmission oil temperature has not changed at least 1.5°C (35°F) for 10 minutes.
P0712
The TCM detects that the transmission oil temperature is less than 1.5°C (35°F) for 5 minutes.
P0713
The TCM detects that the transmission oil temperature is greater than 150°C (302°F) for 12 seconds.
Action Taken When the DTC Sets
* DTC P0711, DTC P0712, and DTC P0713 are Type A DTCs.
* The TCM will disable DTC P1719.
* The TCM will default the transmission oil temperature to 200°C (392°F).
* The TCM inhibits Hot Mode.
* The TCM inhibits Winter Mode.
* No neutral control.
Conditions for Clearing the DTC
DTC P0711, DTC P0712, and DTC P0713 are Type A DTCs.
Reference Information
Schematic Reference
Automatic Transmission Controls Schematics (Electrical Diagrams)
Connector End View Reference
Component Connector End Views (Connector Views)
Description and Operation
Transmission General Information (Transmission General Information)
Electrical Information Reference
* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (Diagnostic Trouble Code Descriptions)
Scan Tool Reference
Control Module References (Programming and Relearning)
Circuit/System Verification
Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data. Ignition ON, observe the DTC information with a scan tool.
Circuit/System Testing
1. Ignition OFF, disconnect the TFT harness at the sensor.
2. Ignition ON, test for 4.8-5.2 volts between the TFT sensor high signal circuit and low signal circuit, harness side.
• If not within the specified range, test the TFT harness for a short to ground or a open/high resistance, If the harness does not test normal, replace the AT wiring harness. If the harness tests normal, replace the TCM.
3. Verify the scan tool TCM, Trans. Fluid Temp. parameter is less than 11°C (52°F).
• If greater than the specified value, replace the TCM.
4. Install a 3-A fused jumper wire between the TFT sensor harness high signal circuit and low signal circuit. Verify the scan tool TCM, Trans. Fluid Temp. parameter is greater than 109°C (228°F).
• If less than the specified value, replace the TCM.
5. If all circuits test normal, test or replace the TFT sensor.
Component Testing
Static Test
1. Place the TFT sensor in water with a temperature of 10°C (50°F). Test for 5.8-7.1K ohms between the TFT sensor high signal circuit and low signal circuit.
• If not within the specified range, replace the TFT sensor.
2. Place the TFT sensor in water with a temperature of 145°C (293°F). Test for 100-120 ohms between the TFT sensor high signal circuit and low signal.
• If not within the specified range, replace the TFT sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Control Module References (Programming and Relearning) for TCM replacement, setup, and programming
* Wiring Harness Removal (Overhaul)
* Wiring Harness Installation (Overhaul)