With Manufacturer's Scan Tool
Read Diagnostic Trouble Code (DTC)OPERATION
1. SUBARU SELECT MONITOR (NORMAL MODE)
1. On the "Main Menu" display screen, select {Each System Check}.
2. On the "System Selection Menu" display screen, select {Engine Control System}.
3. Select the [OK] after the information of engine type has been displayed.
4. On the "Engine Diagnosis" display screen, select {DTC Display}.
5. On the "Diagnostic Code (s) Display" screen, select the {Current Diagnostic Code (s)} or {History Diagnostic Code (s)}.
NOTE:
- For detailed operation procedure, refer to the "SUBARU SELECT MONITOR OPERATION MANUAL".
- For details concerning DTC, refer to "List of Diagnostic Trouble Code (DTC)". List of Diagnostic Trouble Code (DTC)
2. SUBARU SELECT MONITOR (OBD MODE)
1. On the "Main Menu" display screen, select {Each System Check}.
2. On the "System Selection Menu" display screen, select {Engine Control System}.
3. Select the [OK] after the information of engine type has been displayed.
4. On the "Engine Diagnosis" display screen, select {OBD System}.
5. On the "OBD Menu" display screen, select {DTC Display}.
6. Make sure DTC is shown on the screen.
NOTE:
- For detailed operation procedure, refer to the "SUBARU SELECT MONITOR OPERATION MANUAL".
- For details concerning DTC, refer to "List of Diagnostic Trouble Code (DTC)". List of Diagnostic Trouble Code (DTC)
Subaru Select Monitor
OPERATION
1. HOW TO USE SUBARU SELECT MONITOR
1. Prepare the Subaru Select Monitor kit.
2. Connect the diagnosis cable to Subaru Select Monitor.
3. Connect the Subaru Select Monitor to data link connector.
1. Data link connector is located in the lower portion of instrument panel (on the driver's side).
2. Connect the diagnosis cable to data link connector.
CAUTION: Do not connect the scan tools except for Subaru Select Monitor and general scan tool.
4. Turn the ignition switch to ON (engine OFF) and run the Subaru Select Monitor.
5. Using the Subaru Select Monitor, call up DTC and data, then record them.
2. READ DIAGNOSTIC TROUBLE CODE DTC) FOR ENGINE (NORMAL MODE)
Refer to Read Diagnostic Trouble Code for information about how to display a DTC. Reading Diagnostic Trouble Codes
3. READ DIAGNOSTIC TROUBLE CODE DTC) FOR ENGINE (OBD MODE)
Refer to Read Diagnostic Trouble Code for information about how to display a DTC. Reading Diagnostic Trouble Codes
4. READ CURRENT DATA FOR ENGINE (NORMAL MODE)
1. On the "Main Menu" display screen, select {Each System Check}.
2. On the "System Selection Menu" display screen, select {Engine Control System}.
3. Select the [OK] after the information of engine type has been displayed.
4. On the "Engine Diagnosis" display screen, select the {Current Data Display/Save}.
5. On the "Data Display Menu" screen, select the {Data Display}.
6. Using the scroll key, scroll the display screen up or down until the desired data is shown.
Part 1:
Part 2:
- A list of the support data is shown in the table.
5. READ CURRENT DATA FOR ENGINE (OBD MODE)
1. On the "Main Menu" display screen, select {Each System Check}.
2. On the "System Selection Menu" display screen, select {Engine Control System}.
3. Select the [OK] after the information of engine type has been displayed.
4. On the "Engine Diagnosis" display screen, select {OBD System}.
5. On the "OBD system" display screen, select the {Current Data Display/Save}.
6. On the "Data Display Menu" display screen, select the {Data Display}.
7. Using the scroll key, scroll the display screen up or down until the desired data is shown.
Part 1:
Part 2:
- Alist of the support data is shown in the table.
6. READ FREEZE FRAME DATA FOR ENGINE (OBD MODE)
1. On the "Main Menu" display screen, select {Each System Check}.
2. On the "System Selection Menu" display screen, select {Engine Control System}.
3. Select the [OK] after the information of engine type has been displayed.
4. On the "Engine Diagnosis" display screen, select {OBD System}.
5. On the "OBD Menu" display screen, select {Freeze Frame Data}.
- A list of the support data is shown in the table.
7. V.I.N. REGISTRATION
1. On the "Main Menu" display screen, select {Each System Check}.
2. On the "System Selection Menu" display screen, select {Engine Control System}.
3. Select the [OK] after the information of engine type has been displayed.
4. On the "Engine Diagnosis" display screen, select {V.I.N. Registration}.
5. Perform the procedures shown on the display screen.