Subaru Select Monitor
Subaru Select MonitorOPERATION
1. READ DIAGNOSTIC TROUBLE CODE (DTC)
1. Prepare the Subaru Select Monitor kit.
2. Prepare the personal computer which has been installed the Subaru Select Monitor.
3. Connect the USB cable between SDI (Subaru Diagnosis Interface) and USB port on the personal computer (dedicated port for the Subaru Select Monitor).
NOTE: The dedicated port for the Subaru Select Monitor means the USB port which was used to install the Subaru Select Monitor.
4. Connect the diagnosis cable to SDI.
5. Connect the SDI to data link connector located in the lower portion of the instrument panel (on the driver's side).
6. Start a PC.
7. Turn the ignition switch to ON (engine OFF), and run the "PC application for Subaru Select Monitor".
8. Call up DTC and data, then record them.
NOTE: For detailed operation procedure, refer to the "PC application help for Subaru Select Monitor".
2. READ CURRENT DATA
1. On the <
2. On the <
3. Select <
4. Using the scroll key, scroll the display screen up or down until the desired data is shown.
3. DISPLAY OF DATA
NOTE: For details concerning the operation procedure, refer to "PC application help for Subaru Select Monitor".
4. CONFIRMATION OF CURRENT SETTING
1. On <
2. On <
3. On <
4. Using the scroll key, scroll the display screen up or down until the desired data is shown.
5. Display the following item and record the settings.
Required items for new registration (Except for system not equipped)
5. REGISTRATION BODY INTEGRATED UNIT (FUNCTION SETTING)
CAUTION:
Body integrated unit is core of LAN system, and also can select the function of all vehicle system control. It is possible to control the original functions of vehicle when registrations of body integrated unit, or User Customizing are corresponded to vehicle equipment.
If registrations and function setting are different from vehicle equipment, vehicle system does not operate normally and diagnosis cannot be performed correctly. Pay attention to following item.
- Be sure to correspond registrations, or User Customizing settings to vehicle equipment.
- Do not change the settings of vehicle improperly.
- Confirm key illumination does not blink or "Factory or Market setting" of body integrated unit registrations is "Market". If "Factory or Market setting" is set to "Factory," key illumination blinks when ignition key is turned ON, to notify that the settings are unconfirmed.
- Key illumination does not blink with ignition switch turned to ON and go off with door closed.
- Be sure to register immobilizer if body integrated unit is replaced with a new part. (models with immobilizer)
- Make a registration of immobilizer when the parts related to immobilizer have been replaced. Refer to the "PC application help for Subaru Select Monitor".
1. Connect SDI to data link connector located in the lower portion of the instrument panel (on the driver's side).
CAUTION: Do not connect the scan tools other than the Subaru Select Monitor.
2. Start the PC.
3. Turn the ignition switch to ON (engine OFF) and run the "PC application for Subaru Select Monitor".
4. On <
5. On <
6. Click the [OK] button after the control module name {Integrated unit} is displayed.
7. On <
8. Change the setting with UP/DOWN key.
- List of body integrated unit registration item
NOTE: Setting is different depending on the grade of vehicle.
CAUTION:
- To perform normal operation of vehicle and diagnosis, the above settings must match the actual vehicle equipment.
- When body integrated unit is a new part or "Factory" mode, key illumination blinks to show equipment settings have not been completed. Check the detailed procedures of User Customizing.
- Be sure not to change Factory or Market setting except when installing a new body integrated unit.
NOTE:
"Factory" mode:
- Body integrated unit has not been set yet. It can be recognized by key illumination blinking with ignition switch turned to ON.
- All replacement body integrated units are set to "Factory" mode. When replacing a body integrated unit, be sure to perform the registration operation.
"Market" mode:
- Each settings have been set. It can be recognized by key ring illumination coming on in concocting with room light and going off with ignition switch turned to ON.
9. Perform the Factory or Market setting. On the <
10. Change the mode from Factory to Market and then turn the ignition switch to OFF.
11. Change the Subaru Select Monitor system selection to <
12. Perform the operation according to the "PC application help for Subaru Select Monitor".
13. When key registration is completed, "Do you want to register remote engine start?" is displayed. Perform registration only for equipped models.
14. Perform the User Customizing.
NOTE: For details concerning the operation procedure, refer to "PC application help for Subaru Select Monitor".
6. CLEAR MEMORY MODE
1. On <
2. On <
3. Press the [OK] key after the information of body integrated unit type is displayed.
4. On <
5. When "Done" is shown on the display screen, turn the ignition switch to OFF.
NOTE: For details concerning the operation procedure, refer to "PC application help for Subaru Select Monitor".
7. FREEZE FRAME DATA
NOTE:
- Data stored at the time of trouble occurrence is shown on the display.
- Freeze frame data will be memorized maximum to 20.
- If freeze frame data is not stored in memory correctly (caused by low power supply of body integrated unit), DTC will be displayed with "?" on the head of it in the Subaru Select Monitor display. This shows it may be an unreliable reading.
8. USER CUSTOMIZING
1. On <
2. On <
3. On <
4. Change the setting with UP/DOWN key and set with the [OK] key.
- List of User Customizing item
5. After setting, make sure that the setting changed in the {Current Data Display & Save} is same as vehicle equipment.
CAUTION:
- The above settings must match the actual vehicle equipment.
- Do not change settings except for above setting while performing the User Customizing.
- Be sure not to change Factory or Market setting except when installing a new body integrated unit.
NOTE: For details concerning the operation procedure, refer to "PC application help for Subaru Select Monitor".
9. FUNCTION CHECK
In order to check the body integrated unit function, inspect the body integrated unit and actuator using Subaru Select Monitor without operating switches.
1. On <
2. On <
3. On <
4. Select the item to be operated on the <
5. Pressing [Next] starts, [End] cancels the operation and [OK] returns to the System Operation Check Mode display screen.
NOTE: If not equipped (based on area or condition), process will not go on.
INSPECTION
1. COMMUNICATION FOR INITIALIZING IMPOSSIBLE
DETECTING CONDITION:
Faulty harness connectors
TROUBLE SYMPTOM:
Not communicable with Subaru Select Monitor.
WIRING DIAGRAM:
Wiring Diagram:
Step 1-4:
Step 5-12:
CAUTION: For model with immobilizer, immobilizer registration work is necessary when the body integrated unit replaced. For details, refer to the "PC application help for Subaru Select Monitor".