Installation Part 1, Step 1-65

INTERIOR: ROOF HEADLINING: INSTALLATION

INSTALLATION

1. INSTALL REAR ROOF SIDE RAIL PAD LH (w/ Sliding Roof)
(a) Align the markings on the roof headlining assembly with the rear roof side rail pad LH and install the pad using hot melt glue as shown in the illustration.

2. INSTALL REAR ROOF SIDE RAIL PAD RH (w/ Sliding Roof)
(a) Align the markings on the roof headlining assembly with the rear roof side rail pad RH and install the pad using hot melt glue as shown in the illustration.

3. INSTALL ROOF SIDE RAIL GARNISH PAD LH (w/ Sliding Roof)
(a) Align the markings on the roof headlining assembly with the roof side rail garnish pad LH and install the pad using hot melt glue as shown in the illustration.

4. INSTALL ROOF SIDE RAIL GARNISH PAD RH (w/ Sliding Roof)
(a) Align the markings on the roof headlining assembly with the roof side rail garnish pad RH and install the pad using hot melt glue as shown in the illustration.

5. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY Installation

6. INSTALL NO. 1 ROOF WIRE
(a) Peel off the release paper from the double-sided tape.

(b) w/ Vanity Light:
(1) Turn the visor connectors clockwise approximately 90° to install the connectors to the roof headlining.
(c) Attach the No. 1 roof wire along the double-sided tape so that the marking surface of the wire harness faces downward.

Securely attach the No. 1 roof wire. Failure to do so may cause abnormal noise.

7. INSTALL NO. 1 AIR OUTLET REGISTER ASSEMBLY (w/ Rear Air Conditioning System)

(a) Engage the 10 claws and install the No. 1 air outlet register assembly into the roof side air outlet register.
8. INSTALL NO. 2 ROOF HEADLINING SUPPORT
(a) Align the markings on the roof headlining assembly with the No. 2 roof headlining supports and install the headlining supports using hot melt glue as shown in the illustration.

9. INSTALL NO. 4 ROOF SILENCER PAD
(a) Align the markings on the roof headlining assembly with the No. 4 roof silencer pad and install the silencer pad using hot melt glue as shown in the illustration.

10. INSTALL NO. 2 ROOF HEADLINING PAD
(a) Align the markings on the roof headlining assembly with the 2 No. 2 roof headlining pads and install the pads using hot melt glue as shown in the illustration.

11. INSTALL ROOF HEADLINING PAD
(a) Align the markings on the roof headlining assembly with the 2 roof headlining pads and install the pads using hot melt glue as shown in the illustration.

12. INSTALL NO. 1 ROOF HEADLINING SUPPORT
(a) Align the markings on the roof headlining assembly with the 2 No. 1 roof headlining supports and install the headlining supports using hot melt glue as shown in the illustration.

13. INSTALL NO. 2 ROOF SILENCER PAD (w/o Sliding Roof)
(a) Align the markings on the roof headlining assembly with the No. 2 roof silencer pad and install the silencer pad using hot melt glue as shown in the illustration.

14. INSTALL NO. 1 ROOF SILENCER PAD (w/o Sliding Roof)
(a) Align the markings on the roof headlining assembly with the No. 1 roof silencer pad and install the silencer pad using hot melt glue as shown in the illustration.

15. INSTALL REAR NO. 2 SIDE RAIL SPACER LH (w/o Sliding Roof)
(a) Align the markings on the roof headlining assembly with the rear No. 2 side rail spacer LH and install the spacer using hot melt glue as shown in the illustration.

16. INSTALL REAR NO. 2 SIDE RAIL SPACER RH (w/o Sliding Roof)
HINT: Use the same procedure for the RH side and the LH side.

17. INSTALL FRONT SIDE RAIL SPACER LH (w/o Sliding Roof)
(a) Align the markings on the roof headlining assembly with the front side rail spacer LH and install the spacer using hot melt glue as shown in the illustration.

18. INSTALL FRONT SIDE RAIL SPACER RH (w/o Sliding Roof)
HINT: Use the same procedure for the RH side and the LH side.

19. INSTALL VANITY LIGHT ASSEMBLY (w/ Vanity Light)

(a) Engage the 3 claws and install the vanity light assembly.
20. INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)

(a) Pull the roof headlining assembly into the vehicle through the back door.
NOTE: Do not damage the roof headlining assembly or body interior.

(b) Install the 4 clips.
(c) Connect the No. 2 antenna cord sub-assembly connector to the rear pillar RH.
(d) Connect the No. 2 antenna cord sub-assembly connectors and engage the 3 clamps to the front pillar RH.
(e) Install the No. 2 antenna cord sub-assembly to the front pillar RH with the bolt.
(f) Connect the No. 1 roof wire connector and engage the 3 clamps to the front pillar LH.

NOTE: After installation, make sure that the back door weatherstrip does not interfere with the roof headlining assembly.

21. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)

(a) Pull the roof headlining assembly into the vehicle through the back door.
NOTE: Do not damage the roof headlining assembly or body interior.

(b) Install the 3 clips.
(c) Connect the sliding roof drive gear connector.
(d) Connect the No. 2 antenna cord sub-assembly connector to the rear pillar RH.
(e) Connect the No. 2 antenna cord sub-assembly connector and engage the 3 clamps to the front pillar RH.
(f) Install the No. 2 antenna cord sub-assembly to the front pillar RH with the bolt.
(g) w/ Rear Seat Entertainment System:
(1) Connect the No. 1 roof wire connector to the rear pillar LH.
(h) Connect the No. 1 roof wire connectors and engage the 3 clamps to the front pillar LH.

NOTE: After installation, make sure that the back door weatherstrip does not interfere with the roof headlining assembly.

22. INSTALL VISOR HOLDER

(a) Engage the 2 claws.
(b) Push in the visor holder as shown in the illustration.
HINT: Use the same procedure for the RH side and the LH side.

23. INSTALL SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)

(a) Align the joining point of the moulding with the notch of the roof headlining assembly, and install the sun roof opening trim moulding.
NOTE: After installation, check that the corners fit correctly.

24. INSTALL ROOF HEADLINING TRIM CLIP STOPPER

(a) Install the roof headlining trim clip stopper with the bolt.
(b) Engage the 3 claws.
HINT: Use the same procedure for the RH side and the LH side.

25. INSTALL ASSIST GRIP ASSEMBLY (w/ Sliding Roof)

(a) Assemble the assist grip assembly as shown in the illustration.

(b) Install the assist grip assembly.
HINT: Use the same procedure for the other 4 assist grips.

26. INSTALL REAR ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof)

(a) Assemble the rear assist grip sub-assembly as shown in the illustration.

(b) Install the rear assist grip sub-assembly.
HINT: Use the same procedure for the RH side and the LH side.

27. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof)

(a) Assemble the front assist grip sub-assembly as shown in the illustration.

(b) Install the front assist grip sub-assembly.
HINT: Use the same procedure for the RH side and the LH side.

28. INSTALL TELEVISION DISPLAY ASSEMBLY (w/ Rear Seat Entertainment System) Installation

29. INSTALL TELEVISION BASE (w/ Rear Seat Entertainment System) Installation

30. INSTALL NO. 2 ROOM LIGHT ASSEMBLY

(a) Engage the 4 claws and install the lens cover.

(b) Engage the 4 claws and install the room light switch base to the No. 2 room light assembly.

(a) Engage the 4 claws and install the lens cover.

(b) Engage the 4 claws and install the room light switch base to the No. 1 room light assembly.

(c) Engage the 4 claws and install the No. 1 room light assembly.
32. INSTALL NO. 1 ROOM LIGHT ASSEMBLY (for Independent Type)

(a) Engage the 4 claws and install the lens cover.

(b) Engage the 8 claws and install the room light switch base to the No. 1 room light assembly.

(c) Engage the 4 claws and install the No. 1 room light assembly.
33. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror) Installation

34. INSTALL VISOR ASSEMBLY LH

(a) Install the visor assembly LH with the 2 screws.
35. INSTALL VISOR BRACKET COVER (for LH Side)

(a) Engage the 4 claws and install the visor bracket cover.
36. INSTALL VISOR ASSEMBLY RH
HINT: Use the same procedure for the RH side and the LH side.

37. INSTALL VISOR BRACKET COVER (for RH Side)
HINT: Use the same procedure for the RH side and the LH side.

38. INSTALL ROOF CONSOLE BOX ASSEMBLY

(a) Connect the connector.
(b) Engage the 3 guides, 2 clips, fastener, and install the roof console box assembly.
39. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH (w/o Power Back Door)
(a) w/ Rear No. 2 Seat:

(1) Engage the 2 guides and 5 clips.
(2) Install the roof side inner garnish assembly LH with the bolt.

(3) Engage the 2 guides and the 2 claws, and install the No. 2 seat outer belt guide.
(b) w/o Rear No. 2 Seat:

(1) Engage the 2 guides and 5 clips.
(2) Install the roof side inner garnish assembly LH with the bolt.
40. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH (w/ Power Back Door)
(a) w/ Rear No. 2 Seat:

(1) Engage the 2 guides and 5 clips.
(2) Install the roof side inner garnish assembly LH with the bolt.

(3) Engage the 2 guides and the 2 claws, and install the No. 2 seat outer belt guide.
(b) w/o Rear No. 2 Seat:

(1) Engage the 2 guides and 5 clips.
(2) Install the roof side inner garnish assembly LH with the bolt.
41. INSTALL QUARTER PILLAR GARNISH LH

(a) Engage the 2 guides and the 2 clips, and install the quarter pillar garnish LH as shown in the illustration.

(b) Engage the 2 guides and the 2 claws, and install the No. 1 seat outer belt guide.
42. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
(a) Engage the 4 clips and the 7 claws.
(b) Install the 2 clips.
(c) Install the deck trim side panel assembly LH with the 2 bolts.

43. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH Installation

44. INSTALL FRONT DECK SIDE TRIM COVER LH

(a) Engage the 4 claws and install the 2 front deck side trim covers LH.
45. INSTALL NO. 2 DECK SIDE TRIM HOOK

(a) Install the No. 2 deck side trim hook with the screw.
46. INSTALL ROPE HOOK ASSEMBLY (for LH Side)

(a) for Front Side:
(1) Install the rope hook assembly with the bolt.
Torque: 6.5 Nm (66 kgf-cm, 58 in-lbf)
(2) Engage the 2 claws.

(b) for Rear Side:
(1) Install the rope hook assembly with the bolt.
Torque: 6.5 Nm (66 kgf-cm, 58 in-lbf)
(2) Engage the 2 claws.
47. INSTALL REAR DECK TRIM COVER (w/o Remote Folding Function)

(a) Engage the 10 claws and install the rear deck trim cover.
48. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)

(a) Engage the 5 claws and install the reclining remote control bezel lever LH.
49. INSTALL REAR POWER OUTLET SOCKET COVER Installation

50. INSTALL REAR POWER POINT SOCKET ASSEMBLY Installation

51. INSTALL REAR COMBINATION LIGHT SERVICE COVER LH

(a) Engage the 2 guides and 6 claws, and install the rear combination light service cover LH.
52. INSTALL SIDE TRIM COVER LH (w/o Rear Seat Entertainment System)

(a) Engage the 10 claws and install the side trim cover LH.
53. INSTALL POWER OUTLET SOCKET BEZEL (w/ Rear Seat Entertainment System)

(a) Connect each connector.

(b) Engage the 4 claws and install the power outlet socket bezel.
54. INSTALL DECK SIDE TRIM LH

(a) Engage the 3 guides and 4 claws as shown in the illustration.

(b) Install the deck side trim LH with the bolt.
55. INSTALL DECK SIDE TRIM COVER LH

(a) Engage the 2 claws and install the deck side trim cover LH.
56. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH (w/o Rear No. 2 Seat)
HINT: Use the same procedure for the RH side and the LH side.

57. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH (w/ Rear No. 2 Seat)
HINT: Use the same procedure for the RH side and the LH side.

58. INSTALL QUARTER PILLAR GARNISH RH
HINT: Use the same procedure for the RH side and the LH side.

59. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
(a) Engage the 4 clips and the 7 claws.
(b) Install the 2 clips.
(c) Install the deck trim side panel assembly RH with the 3 bolts.

60. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH
HINT: Use the same procedure for the RH side and the LH side.

61. INSTALL FRONT DECK SIDE TRIM COVER RH
HINT: Use the same procedure for the RH side and the LH side.

62. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
HINT: Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.

63. INSTALL ROPE HOOK ASSEMBLY (for RH Side)
HINT: Use the same procedure for the RH side and the LH side.

64. INSTALL REAR COMBINATION LIGHT SERVICE COVER RH

(a) Engage the 2 guides and 6 claws, and install the rear combination light service cover RH.
65. INSTALL REAR ROOM TEMPERATURE SENSOR (w/ Rear Automatic Air Conditioning System) Installation

Proceed to Installation Part 2, Step 66-130 Installation Part 2, Step 66-130