B0126

SUPPLEMENTAL RESTRAINT SYSTEM: AIRBAG SYSTEM: B0126/27: Seat Belt Buckle Switch LH Circuit Malfunction

DTC B0126/27 - Seat Belt Buckle Switch LH Circuit Malfunction

DESCRIPTION

The seat belt buckle switch LH circuit consists of the center airbag sensor assembly and the front seat inner belt assembly LH.
DTC B0126/27 is recorded when a malfunction is detected in the seat belt buckle switch LH circuit.






WIRING DIAGRAM





INSPECTION PROCEDURE

PROCEDURE

1. CHECK DTC





(a) Turn the ignition switch to the ON position, and wait for at least 60 seconds.
(b) Clear the DTCs stored in memory .
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at least 60 seconds.
(e) Check the DTCs .
OK:
DTC B0126/27 is not output.
HINT: Codes other than code B0126/27 may be output at this time, but they are not related to this check.

NG -- CHECK CONNECTION OF CONNECTORS
OK -- USE SIMULATION METHOD TO CHECK
2. CHECK CONNECTION OF CONNECTORS
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(c) Check that the connectors are properly connected to the center airbag sensor assembly and the front seat inner belt assembly LH.
OK:
The connectors are connected.
NG -- CONNECT CONNECTORS
OK -- Continue to next step.
3. CHECK VEHICLE
(a) Check the front driver seat type.
Result:






B -- CHECK FLOOR WIRE (OPEN)
A -- Continue to next step.
4. CHECK FLOOR WIRE (OPEN)





(a) Disconnect the connectors from the center airbag sensor assembly and the front seat inner belt assembly LH.
(b) Using a service wire, connect A20-19 (LBE+) and A20-2 (LBE-) of connector "B".
NOTE: Do not forcibly insert a service wire into the terminals of the connector when connecting.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:






NG -- REPAIR OR REPLACE FLOOR WIRE
OK -- Continue to next step.
5. CHECK FLOOR WIRE (SHORT TO B+)





(a) Disconnect the service wire from connector "B".
(b) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(c) Turn the ignition switch to the ON position.
(d) Measure the voltage according to the value(s) in the table below.
Standard voltage:






NG -- REPAIR OR REPLACE FLOOR WIRE
OK -- Continue to next step.
6. CHECK FLOOR WIRE (SHORT TO GROUND)





(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:






NG -- REPAIR OR REPLACE FLOOR WIRE
OK -- Continue to next step.
7. CHECK FLOOR WIRE (SHORT)





(a) Measure the voltage according to the value(s) in the table below.
Standard resistance:






NG -- REPAIR OR REPLACE FLOOR WIRE
OK -- Continue to next step.
8. CHECK FRONT SEAT INNER BELT ASSEMBLY LH





(a) Connect the connectors to the front seat inner belt assembly LH and the center airbag sensor assembly.
(b) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(c) Turn the ignition switch to the ON position, and wait for at least 60 seconds.
(d) Clear the DTCs stored in memory .
(e) Turn the ignition switch to the LOCK position.
(f) Turn the ignition switch to the ON position, and wait for at least 60 seconds.
(g) Check the DTCs .
OK:
DTC B0126/27 is not output.
HINT: Codes other than code B0126/27 may be output at this time, but they are not related to this check.

NG -- REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
OK -- USE SIMULATION METHOD TO CHECK
9. REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(c) Replace the front seat inner belt assembly LH .
HINT: Perform the inspection using parts from a normal vehicle if possible.

NEXT -- Continue to next step.
10. CHECK CENTER AIRBAG SENSOR ASSEMBLY





(a) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(b) Turn the ignition switch to the ON position, and wait for at least 60 seconds.
(c) Clear the DTCs stored in memory .
(d) Turn the ignition switch to the LOCK position.
(e) Turn the ignition switch to the ON position, and wait for at least 60 seconds.
(f) Check the DTCs .
OK:
DTC B0126/27 is output.
HINT: Codes other than code B0126/27 may be output at this time, but they are not related to this check.

NG -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK -- END
11. CHECK FLOOR WIRE (OPEN)





(a) Disconnect the connectors from the center airbag sensor assembly and the front seat inner belt assembly LH.
(b) Using a service wire, connect A20-19 (LBE+) and A20-2 (LBE-) of connector "B".
NOTE: Do not forcibly insert a service wire into the terminals of the connector when connecting.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:






NG -- REPAIR OR REPLACE FLOOR WIRE
OK -- Continue to next step.
12. CHECK FLOOR WIRE (SHORT TO B+)





(a) Disconnect the service wire from connector "B".
(b) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(c) Turn the ignition switch to the ON position.
(d) Measure the voltage according to the value(s) in the table below.
Standard voltage:






NG -- REPAIR OR REPLACE FLOOR WIRE
OK -- Continue to next step.
13. CHECK FLOOR WIRE (SHORT TO GROUND)





(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:






NG -- REPAIR OR REPLACE FLOOR WIRE
OK -- Continue to next step.
14. CHECK FLOOR WIRE (SHORT)





(a) Measure the resistance according to the value(s) in the table below.
Standard resistance:






NG -- REPAIR OR REPLACE FLOOR WIRE
OK -- Continue to next step.
15. CHECK FRONT SEAT INNER BELT ASSEMBLY LH





(a) Connect the connectors to the front seat inner belt assembly LH and the center airbag sensor assembly.
(b) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(c) Turn the ignition switch to the ON position, and wait for at least 60 seconds.
(d) Clear the DTCs stored in memory .
(e) Turn the ignition switch to the LOCK position.
(f) Turn the ignition switch to the ON position, and wait for at least 60 seconds.
(g) Check the DTCs .
OK:
DTC B0126/27 is not output.
HINT: Codes other than code B0126/27 may be output at this time, but they are not related to this check.

NG -- REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
OK -- USE SIMULATION METHOD TO CHECK
16. REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(c) Replace the front seat inner belt assembly LH .
HINT: Perform the inspection using parts from a normal vehicle if possible.

NEXT -- Continue to next step.
17. CHECK CENTER AIRBAG SENSOR ASSEMBLY





(a) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(b) Turn the ignition switch to the ON position, and wait for at least 60 seconds.
(c) Clear the DTCs stored in memory .
(d) Turn the ignition switch to the LOCK position.
(e) Turn the ignition switch to the ON position, and wait for at least 60 seconds.
(f) Check the DTCs .
OK:
DTC B0126/27 is not output.
HINT: Codes other than code B0126/27 may be output at this time, but they are not related to this check.

NG -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK -- END