B1214

MULTIPLEX COMMUNICATION: MULTIPLEX COMMUNICATION SYSTEM: B1214: Short to B+ in Door System Communication Bus Malfunction

DTC B1214 - Short to B+ in Door System Communication Bus Malfunction

DTC B1215 - Short to GND in Door System Communication Bus Malfunction

DESCRIPTION

DTCs B1214 and B1215 are output when a short to +B or the body ground occurs on the communication bus. Detecting this condition disables all the BEAN communication and outputs some DTCs.






WIRING DIAGRAM





INSPECTION PROCEDURE
NOTE: Disconnect connectors in operational sequence, and start the next operation after the connectors are connected.

PROCEDURE

1. CHECK DTC (MULTIPLEX NETWORK BODY ECU - COMBINATION METER)
(a) Check the DTC when the B7 connector of the multiplex network body ECU and the combination meter connector are disconnected.





OK:
DTC B1214 or B1215 is not output.
HINT: When the output of the DTC stops, there is a malfunction between the B7 connector of the multiplex network body ECU and the combination meter.

NG -- CHECK DTC (POWER SLIDE DOOR ECU LH)
OK -- Continue to next step.
2. CHECK DTC (COMBINATION METER)
(a) Check whether the output of the DTC stops when the combination meter connector is disconnected.





OK:
DTC B1214 or B1215 is not output.
HINT: When the output of the DTC stops, the combination meter is malfunctioning.

OK -- REPLACE COMBINATION METER
NG -- Continue to next step.
3. CHECK DTC (A/C AMPLIFIER)
(a) Check whether the output of the DTC stops when the A/C amplifier connector is disconnected.





OK:
DTC B1214 or B1215 is not output.
HINT: When the output of the DTC stops, the A/C amplifier is malfunctioning.

OK -- REPLACE A/C AMPLIFIER
NG -- Continue to next step.
4. CHECK HARNESS AND CONNECTOR (COMBINATION METER - A/C AMPLIFIER)
(a) Check whether the output of the DTC stops when the combination meter connector and the A/C amplifier connector are disconnected.





OK:
DTC B1214 or B1215 is not output.
HINT: When the output of the DTC stops, the wire harness between the combination meter and the A/C amplifier is malfunctioning.

OK -- REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER - A/C AMPLIFIER)
NG -- Continue to next step.
5. CHECK DTC (AIRBAG SENSOR ASSEMBLY)
(a) Check whether the output of the DTC stops when the airbag sensor assembly connector is disconnected.





OK:
DTC B1214 or B1215 is not output.
HINT: When the output of the DTC stops, the airbag sensor assembly is malfunctioning.

OK -- REPLACE AIRBAG SENSOR ASSEMBLY
NG -- Continue to next step.
6. CHECK HARNESS AND CONNECTOR (A/C AMPLIFIER - AIRBAG SENSOR ASSEMBLY)
(a) Check whether the output of the DTC stops when the A/C amplifier connector and the airbag sensor assembly connector are disconnected.





OK:
DTC B1214 or B1215 is not output.
HINT: When the output of the DTC stops, the wire harness between the A/C amplifier and airbag sensor assembly is malfunctioning.

OK -- REPAIR OR REPLACE HARNESS OR CONNECTOR (A/C AMPLIFIER - AIRBAG SENSOR ASSEMBLY)
NG -- Continue to next step.
7. CHECK DTC (MULTIPLEX NETWORK BODY ECU)
(a) Check whether the output of the DTC stops when the B7 and 1E connectors of the multiplex network body ECU are disconnected.





OK:
DTC B1214 or B1215 is not output.
HINT: When the output of the DTC stops, the multiplex network body ECU is malfunctioning.

OK -- REPLACE MULTIPLEX NETWORK BODY ECU
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR (AIRBAG SENSOR ASSEMBLY - MULTIPLEX NETWORK BODY ECU)
8. CHECK DTC (POWER SLIDE DOOR ECU LH)
(a) Check whether the output of the DTC stops when the power slide door ECU LH connector is disconnected.





OK:
DTC B1214 or B1215 is not output.
HINT: When the output of the DTC stops, the power slide door ECU LH is malfunctioning.

OK -- REPLACE POWER SLIDE DOOR ECU LH
NG -- Continue to next step.
9. CHECK DTC (POWER SLIDE DOOR ECU RH)
(a) Check whether the output of the DTC stops when the power slide door ECU RH connector is disconnected.





OK:
DTC B1214 or B1215 is not output.
HINT: When the output of the DTC stops, the power slide door ECU RH is malfunctioning.

OK -- REPLACE POWER SLIDE DOOR ECU RH
NG -- Continue to next step.
10. CHECK DTC (POWER BACK DOOR ECU)
(a) Check whether the output of the DTC stops when the power back door ECU connector is disconnected.





OK:
DTC B1214 or B1215 is not output.
HINT: When the output of the DTC stops, the power back door ECU is malfunctioning.

OK -- REPLACE POWER BACK DOOR ECU
NG -- Continue to next step.
11. CONFIRM MODEL
Result:






B -- CHECK HARNESS AND CONNECTOR
A -- Continue to next step.
12. CHECK DTC (SEAT POSITION CONTROL ECU)
(a) Check whether the output of the DTC stops when the seat position control ECU connector is disconnected.





OK:
DTC B1214 or B1215 is not output.
HINT: When the output of the DTC stops, the seat position control ECU is malfunctioning.

OK -- REPLACE SEAT POSITION CONTROL ECU
NG -- Continue to next step.
13. CHECK DTC (OUTER MIRROR CONTROL ECU LH)
(a) Check whether the output of the DTC stops when the outer mirror control ECU LH connector is disconnected.





OK:
DTC B1214 or B1215 is not output.
HINT: When the output of the DTC stops, the outer mirror control ECU LH is malfunctioning.

OK -- REPLACE OUTER MIRROR CONTROL ECU LH
NG -- Continue to next step.
14. CHECK DTC (OUTER MIRROR CONTROL ECU RH)
(a) Check whether the output of the DTC stops when the outer mirror control ECU RH connector is disconnected.





OK:
DTC B1214 or B1215 is not output.
HINT: When the output of the DTC stops, the outer mirror control ECU RH is malfunctioning.

OK -- REPLACE OUTER MIRROR CONTROL ECU RH
NG -- Continue to next step.
15. CHECK HARNESS AND CONNECTOR
(a) Check for a short to +B or body ground.
(b) Disconnect the multiplex network gateway ECU, combination meter, power slide door ECU LH, power slide door ECU RH, power back door ECU, seat position control ECU (*1), outer mirror control ECU LH (*1), outer mirror control ECU RH (*1) and the B7 connector of the multiplex network body ECU.





HINT: *1: with Driving position memory
(c) Measure the voltage according to the value(s) in the table below.
Standard voltage:





HINT: *1: with Driving position memory
(d) Measure the resistance according to the value(s) in the table below.
Standard resistance:





HINT: *1: with Driving position memory

NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- REPLACE MULTIPLEX NETWORK GATEWAY ECU