P2A00
1GR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P2A00: A/F Sensor Circuit Slow Response (Bank 1 Sensor 1)
DTC P2A00 - A/F Sensor Circuit Slow Response (Bank 1 Sensor 1)
DTC P2A03 - A/F Sensor Circuit Slow Response (Bank 2 Sensor 1)
CAUTION / NOTICE / HINT
HINT:
- DTC P2A00 means malfunctions related to the bank 1 A/F sensor.
- DTC P2A03 means malfunctions related to the bank 2 A/F sensor.
- Bank 1 refers to the bank that includes cylinder No. 1.
- Bank 2 refers to the bank that includes cylinder No. 2.
- Sensor 1 refers to the sensor mounted of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.
DESCRIPTION
The A/F sensor generates a voltage* that corresponds to the actual air-fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air-fuel ratio. The ECM determines the deviation from the stoichiometric air-fuel ratio level, and regulates the fuel injection time. If the A/F sensor malfunctions, the ECM is unable to control the air-fuel ratio accurately.
The A/F sensor is the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. The heat generated by the heater is conducted to the solid electrolyte though the alumina, therefore the sensor activation is accelerated.
In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.
*: Value changes inside the ECM. Since the A/F sensor is the current output element, a current is converted to a voltage inside the ECM. Any measurements taken at the A/F sensor or ECM connectors will show a constant voltage.
MONITOR DESCRIPTION
After engine is warmed up, the ECM performs air-fuel ratio feedback control to regulate the air-fuel ratio at stoichiometric ratio. In addition, this vehicle performs Active A/F Ratio Control for approximately 10 seconds after preconditions met in order to measure the A/F sensor response rate. During active air-fuel ratio control, the ECM forcibly increases and decreases the injection volume for certain amount based on learned stoichiometric air-fuel ratio during usual air-fuel feedback control, and measures the A/F sensor response rate. The ECM calculates the signal from the A/F sensor while performing the active A/F ratio control and interprets the calculated value as a test value for A/F sensor response rate deterioration level.
If the test value for A/F sensor response rate deterioration level is less than threshold, ECM interprets this as a malfunction, and sets the DTC.
CONFIRMATION DRIVING PATTERN
HINT: Performing this confirmation pattern will activate the A/F sensor response monitor.
- (a) Connect the Techstream to the DLC3.
- (b) Turn the ignition switch on.
- (c) Turn the tester on.
- (d) Clear DTCs DTC Check / Clear.
- (e) Enter the following menus: Powertrain / Engine and ECT / Monitor / O2 Sensor / Details.
- (f) Check that RES RATE B1S1 and RES RATE B2S1 are Incomplete.
- (g) Start the engine and warm it up.
- (h) Drive the vehicle at between 25 mph and 75 mph (40 km/h and 120 km/h) for 3 minutes. However, the vehicle should be driven at a constant speed.
- (i) Check the monitor result values on the Techstream by entering the following menus: Powertrain / Engine and ECT / Monitor / O2 Sensor / Details / RES RATE B1S1 or RES RATE B2S1 / Details.
- (j) If the values indicated on the tester do not change, perform READINESS MONITOR DRIVE PATTERN for the A/F sensor and the heated oxygen sensor Monitors, Trips, Drive Cycles and Readiness Codes.
HINT: Completion of all A/F sensor monitors is required to change the value in RES RATE B1S1 and RES RATE B2S1.
- (k) Note the value of the RES RATE B1S1 and RES RATE B2S1.
- (l) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
- (m) Check if any DTCs (any pending DTCs) are set.
MONITOR STRATEGY
TYPICAL ENABLING CONDITIONS
TYPICAL MALFUNCTION THRESHOLDS
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F sensor operation using the Techstream.
1. Connect the Techstream to the DLC3.
2. Start the engine and turn the tester on.
3. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
4. On the tester, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
5. Perform the Active Test operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
6. Monitor the output voltages of the A/F and HO2 sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the tester.
HINT:
- The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
- Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
NOTE: The Air-Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.
- Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
- To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.
HINT:
- DTC P2A00 or P2A03 may be also set, when the air-fuel ratio is stuck rich or lean.
- A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
- A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.
- Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
PROCEDURE
1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00 AND/OR P2A03)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch on.
(c) Turn the tester on.
(d) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(e) Read DTCs.
Result:
HINT:
If any DTCs other than P2A00 or P2A03 are output, troubleshoot those DTCs first.
B -- GO TO DTC CHART
A -- Continue to next step.
2. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
(a) Disconnect the A12 or A13 A/F sensor connector.
(b) Measure the resistance between the terminals of the A/ sensor connector.
Standard resistance:
Bank 1
Bank 2
(c) Reconnect the A/F sensor connector.
NG -- REPLACE AIR FUEL RATIO SENSOR
OK -- Continue to next step.
3. CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
(a) Disconnect the A12 or A13 A/F sensor connector.
(b) Turn the ignition switch on.
(c) Measure the voltage between the +B terminal of the A/F sensor connector and body ground.
Standard voltage:
(d) Turn the ignition switch off.
(e) Disconnect the E5 ECM connector.
(f) Measure the resistance between the terminals of the A/F sensor connector and ECM connector.
Standard resistance (Check for open):
Standard resistance (Check for short):
(g) Reconnect the ECM connector.
(h) Reconnect the A/F sensor connector.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
4. PERFORM CONFIRMATION DRIVING PATTERN
NEXT -- Continue to next step.
5. CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03)
(a) Read DTCs using the Techstream.
(b) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Result:
B -- CHECK FOR INTERMITTENT PROBLEMS
A -- Continue to next step.
6. REPLACE AIR FUEL RATIO SENSOR
NEXT -- Continue to next step.
7. PERFORM CONFIRMATION DRIVING PATTERN
NEXT -- Continue to next step.
8. CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03)
(a) Read DTCs using the Techstream.
(b) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Result:
B -- CHECK EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO (REFER TO DTC P0171 PROCEDURE) P0171
A -- END