Installation
A750E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISSION ASSEMBLY (for 1GR-FE): INSTALLATION
INSTALLATION
1. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY
(a) Using calipers and a straight edge, measure dimension A between the transmission and the end surface of the drive plate.
(b) Aligning the matchmarks on the transmission case and torque converter assembly, engage the splines of the input shaft and turbine runner.
(c) Engage the splines of the stator shaft and stator while turning the torque converter assembly.
HINT: Turn the torque converter assembly approximately 180°.
(d) Turn the torque converter assembly and align the matchmarks on the torque converter assembly and transmission case to engage the key of the oil pump drive gear into the slot on the torque converter assembly. (procedure "1")
NOTE: Do not push on the torque converter when aligning the matchmarks.
(e) Using calipers and a straight edge, measure dimension B shown in the illustration and check that B is greater than A measured in procedure "1".
Standard:
A + 1 mm (0.03937 in.) or more
2. INSTALL NO.1 TRANSMISSION CONTROL CABLE BRACKET
(a) Install the No. 1 transmission control cable bracket to the transmission assembly with the 2 bolts.
Torque: 14 Nm (143 kgf-cm, 10 ft-lbf)
3. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY
(a) Install the automatic transmission assembly to the engine with the 9 bolts.
17 mm head - Torque: 71 Nm (720 kgf-cm, 53 ft-lbf)
14 mm head - Torque: 37 Nm (380 kgf-cm, 27 ft-lbf)
(b) Install the 6 torque converter mounting bolts.
Torque: 48 Nm (490 kgf-cm, 35 ft-lbf)
HINT: First install the black colored bolt and then the remaining 5 bolts.
(c) Install the torque converter housing side cover to the engine.
4. INSTALL NO.1 REAR ENGINE MOUNTING INSULATOR
(a) Install the No. 1 rear engine mounting insulator to the automatic transmission with the 4 bolts.
Torque: 65 Nm (663 kgf-cm, 48 ft-lbf)
5. INSTALL NO.2 MANIFOLD STAY
6. INSTALL MANIFOLD STAY
7. INSTALL STARTER ASSEMBLY
HINT: Installation for Standard or Installation for Cold Area)
8. CONNECT CONNECTOR
(a) Connect the speed sensor SP2 connector.
(b) Install the wire harness with the bolt.
Torque: 8.0 Nm (83 kgf-cm, 71 in-lbf)
(c) Connect the speed sensor NT connector (a).
(d) Connect the transmission wire connector (b).
(e) Connect the park/neutral position switch assembly connector (c).
9. INSTALL NO.3 FRAME CROSSMEMBER SUB-ASSEMBLY
(a) Install the No. 3 frame crossmember sub-assembly with the 4 bolts and 4 nuts.
A - Torque: 72 Nm (735 kgf-cm, 53 ft-lbf)
(b) Tighten the 4 bolts to the No. 3 frame crossmember sub-assembly and No. 1 engine mounting insulator rear.
B - Torque: 18 Nm (184 kgf-cm, 13 ft-lbf)
10. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
(a) Connect the transmission control cable assembly to the automatic transmission.
(b) Install the nut and clip on the transmission control cable assembly.
Torque: 14 Nm (143 kgf-cm, 10 ft-lbf)
11. INSTALL NO.1 OIL COOLER OUTLET TUBE
(a) Temporarily install the No. 1 oil cooler outlet tube.
(b) Temporarily install the No. 1 oil cooler inlet tube.
(c) Install the 2 clamps and 2 bolts.
Torque: 5 Nm (50 kgf-cm, 43 in-lbf)
(d) Using a union nut wrench, tighten the No. 1 oil cooler outlet tube.
Torque: 34 Nm (346 kgf-cm, 25 ft-lbf)
12. INSTALL NO.1 OIL COOLER INLET TUBE
(a) Using a union nut wrench, tighten the No. 1 oil cooler inlet tube.
Torque: 34 Nm (346 kgf-cm, 25 ft-lbf)
13. INSTALL FRONT SUSPENSION MEMBER BRACKET LH
(a) Install the front suspension member bracket LH with the 4 bolts.
Torque: 33 Nm (336 kgf-cm, 24 ft-lbf)
14. INSTALL FRONT SUSPENSION MEMBER BRACKET
(a) Install the front suspension member bracket with the 4 bolts.
Torque: 33 Nm (336 kgf-cm, 24 ft-lbf)
15. INSTALL PROPELLER SHAFT ASSEMBLY Installation
16. INSTALL EXHAUST PIPE
HINT: Installation
17. INSTALL OXYGEN SENSOR
HINT: Installation
18. INSTALL NO.1 ENGINE UNDER COVER SUB-ASSEMBLY
19. INSTALL REAR ENGINE UNDER COVER ASSEMBLY
20. ADD AUTOMATIC TRANSMISSION FLUID
HINT: Procedures
21. INSPECT AUTOMATIC TRANSMISSION FLUID
HINT: Procedures
22. ADJUST SHIFT LEVER POSITION
HINT: Adjustments
23. INSPECT SHIFT LEVER POSITION
HINT: Adjustments
24. CHECK FOR EXHAUST GAS LEAKS
HINT: Installation
25. RESET MEMORY
NOTE: Perform the RESET MEMORY (AT initialization) when replacing the automatic transmission assembly, engine assembly or ECM Programming and Relearning.
HINT: RESET MEMORY cannot be completed by only disconnecting the battery terminal.