Programming and Relearning

BRAKE CONTROL: VEHICLE STABILITY CONTROL SYSTEM: CALIBRATION

CALIBRATION

1. DESCRIPTION

- After replacing the VSC relevant components or performing "Front wheel alignment adjustment", clearing and reading the sensor calibration data is necessary.
- Follow the chart to perform calibration.

HINT: For a rear air suspension vehicle, it is necessary to obtain zero point calibration data (again) after adjusting vehicle height.





2. CLEAR ZERO POINT CALIBRATION (SST CHECK WIRE)

HINT: After replacing the yaw rate and acceleration sensor, make sure to clear zero point calibration data in the skid control ECU and perform zero point calibration.

(a) Turn the ignition switch to ON.





(b) Using SST, connect and disconnect terminals TS and CG of the DLC3 4 times or more within 8 seconds.
SST: 09843-18040





(c) Check that the warning light indicates the normal system code.

(d) Using a check wire, perform zero point calibration of the yaw rate and acceleration sensor.
3. PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR (SST CHECK WIRE)
After replacing the master cylinder solenoid and/or yaw rate and acceleration sensor, make sure to perform yaw rate and acceleration sensor zero point calibration.

NOTICE:
- While obtaining the zero point, do not vibrate the vehicle by tilting, moving or shaking it and keep it in a stationary condition. (Do not start the engine.)
- Be sure to perform calibration on a level surface (with an inclination of less than 1°).

(a) Procedures for test mode:
(1) Turn the ignition switch off.




(2) Using SST, connect terminals TS and CG of the DLC3.
SST: 09843-18040
(3) Check that the steering wheel is in the straight- ahead position and more the shift lever to the P position.

NOTE:
DTC C1210/36 and C1336/39 will be recorded if the shift lever is not in the P position C1210.
(4) Turn the ignition switch to ON.
(5) Keep the vehicle in a stationary condition on a level surface for 2 seconds or more.




(6) Check that the VSC OFF indicator light is blinking in test mode.

NOTE:
The VSC OFF indicator light stays on when obtaining the zero point.
- If the VSC OFF indicator light does not blink, perform the zero point calibration again.
- The zero point calibration is performed only once after the system enters test mode.
- Calibration cannot be performed again until the stored data is cleared once.

4. CLEAR ZERO POINT CALIBRATION (TECHSTREAM)
After replacing the yaw rate and acceleration sensor, make sure to clear zero point calibration data in the skid control ECU and perform zero point calibration.
(a) Connect Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Operate Techstream to erase the codes.
(d) Using Techstream, perform zero point calibration of the yaw rate and acceleration sensor.
5. PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR (TECHSTREAM)
After replacing the master cylinder solenoid and/or yaw rate and acceleration sensor, make sure to perform yaw rate and acceleration sensor zero point calibration.

NOTICE:
- While obtaining the zero point, do not vibrate the vehicle by tilting, moving or shaking it and keep it in a stationary condition. (Do not start the engine.)
- Be sure to perform calibration on a level surface (with an inclination of less than 1°).

(a) Procedures for test mode:
(1) Check that the steering wheel is in the straight-ahead position and move the shift lever to the P position.

NOTE:
DTC C1210/36 and C1336/39 will be recorded if the shift lever is not in the P position C1210.
(2) Connect Techstream to the DLC3.
(3) Turn the ignition switch to ON.
(4) Set Techstream to test mode ("Test Mode").

HINT:
Refer to the Techstream operator's manual for further details.
(5) Keep the vehicle in a stationary condition on a level surface for 2 seconds or more.




(6) Check that the VSC OFF indicator light is blinking in test mode.

NOTE:
The VSC OFF indicator light stays on when obtaining the zero point.
- If the VSC OFF indicator light does not blink, perform the zero point calibration again.
- The zero point calibration is performed only once after the system enters test mode.
- Calibration cannot be performed again until the stored data is cleared once.