Operation CHARM: Car repair manuals for everyone.
Home >> Toyota Truck >> 2009 >> Highlander 4WD V6-3.5L (2GR-FE) >> Repair and Diagnosis >> A L L Diagnostic Trouble Codes ( DTC ) >> Testing and Inspection >> P Code Charts >> P0117

P0117








2GR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0115,P0117,P0118: Engine Coolant Temperature Circuit

DTC P0115 - Engine Coolant Temperature Circuit

DTC P0117 - Engine Coolant Temperature Circuit Low Input

DTC P0118 - Engine Coolant Temperature Circuit High Input

DESCRIPTION

A thermistor is built into the engine coolant temperature sensor, of which the resistance value varies according to the engine coolant temperature.
The structure of the sensor and its connection to the ECM are the same as those of the intake air temperature sensor.
HINT: When any of DTCs P0115, P0117 and P0118 are set, the ECM enters fail-safe mode. During fail-safe mode, the engine coolant temperature is estimated to be 80°C (176°F) by the ECM. Fail-safe mode continues until a pass condition is detected.





HINT: When any of these DTCs are set, check the engine coolant temperature by selecting the following menu items: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.





MONITOR DESCRIPTION

The engine coolant temperature sensor is used to monitor the engine coolant temperature. The engine coolant temperature sensor has a thermistor with a resistance that varies according to the temperature of the engine coolant. When the coolant temperature becomes low, the resistance in the thermistor increases. When the temperature becomes high, the resistance drops.
These variations in resistance are reflected in the voltage output from the sensor. The ECM monitors the sensor voltage and uses this value to calculate the engine coolant temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a fault in the engine coolant temperature sensor and sets a DTC.

Example:
If the sensor voltage output is -40°C (-40°F) for 0.5 seconds or more, the ECM determines that there is an open in the engine coolant temperature sensor circuit, and sets DTC P0118. Conversely, if the voltage output is more than 140°C (284°F) for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit, and sets DTC P0117.
If the malfunction is not repaired successfully, a DTC is set 0.5 seconds after the engine is next started.

MONITOR STRATEGY





TYPICAL ENABLING CONDITIONS





TYPICAL MALFUNCTION THRESHOLDS

P0115:





P0117:





P0118:





COMPONENT OPERATING RANGE





WIRING DIAGRAM





INSPECTION PROCEDURE
HINT:
- If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
- Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

PROCEDURE

1. READ VALUE USING TECHSTREAM (ENGINE COOLANT TEMPERATURE)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch on (IG).
(c) Turn the tester on.
(d) Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.
(e) Read the value displayed on the tester.
Standard:
Between 80°C and 97°C (176°F and 207°F) with warm engine.
Result:





HINT:
- If there is an open circuit, the Techstream indicates -40°C (-40°F).
- If there is a short circuit, the Techstream indicates 140°C (284°F) or higher.

C -- CHECK FOR INTERMITTENT PROBLEMS
B -- READ VALUE USING TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS)
A -- Continue to next step.
2. READ VALUE USING TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS)




(a) Disconnect the engine coolant temperature sensor connector.
(b) Connect terminals 1 and 2 of the engine coolant temperature sensor connector on the wire harness side.
(c) Connect the Techstream to the DLC3.
(d) Turn the ignition switch on (IG).
(e) Turn the tester on.
(f) Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.
(g) Read the value displayed on the tester.
Standard:
140°C (284°F) or higher
(h) Reconnect the engine coolant temperature sensor connector.
NG -- CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
OK -- REPLACE ENGINE COOLANT TEMPERATURE SENSOR
3. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)




(a) Confirm and connection at the engine coolant temperature sensor.
(b) Disconnect the engine coolant temperature sensor connector.
(c) Connect terminals THW and E2 of the ECM connector.
HINT: Before checking, do visual and contact pressure checks on the ECM connector.
(d) Connect the Techstream to the DLC3.
(e) Turn the ignition switch on (IG).
(f) Turn the tester on.
(g) Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.
(h) Read the value displayed on the tester.
Standard:
140°C (284°F) or higher
(i) Reconnect the engine coolant temperature sensor connector.
NG -- REPLACE ECM
OK -- REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
4. READ VALUE USING TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS)




(a) Disconnect the engine coolant temperature sensor connector.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch on (IG).
(d) Turn the tester on.
(e) Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.
(f) Read the value displayed on the tester.
Standard:
-40°C (-40°F)
(g) Reconnect the engine coolant temperature sensor connector.
NG -- CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
OK -- REPLACE ENGINE COOLANT TEMPERATURE SENSOR
5. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)




(a) Disconnect the engine coolant temperature sensor connector.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch on (IG).
(d) Turn the tester on.
(e) Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.
(f) Read the value displayed on the tester.
Standard:
-40°C (-40°F)
(g) Reconnect the engine coolant temperature sensor connector.
NG -- REPLACE ECM
OK -- REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
pro multis · About Operation CHARM