Installation
INTERIOR PANELS / TRIM: ROOF HEADLINING: INSTALLATION
HINT
A bolt without a torque specification is shown in the standard bolt chart Standard Bolt - Specified Torque For Standard Bolts.
1. INSTALL DECK SIDE TRIM CUP HOLDER LH (w/ Rear No. 2 Seat)
(a) Attach the 2 claws to install the deck side trim cup holder.
(b) Install the 4 screws.
2. INSTALL DECK SIDE TRIM CUP HOLDER RH (w/ Rear No. 2 Seat)
HINT
Use the same procedure described for the LH side.
3. INSTALL QUARTER TRIM LID SUB-ASSEMBLY RH (w/ Rear No. 2 Seat)
(a) Attach the 4 claws and 2 guides to install the quarter trim lid.
4. INSTALL REAR SEAT SHOULDER BELT HANGER LH (w/ Rear No. 2 Seat)
(a) Attach the claw and guide to install the rear seat shoulder belt hanger.
5. INSTALL REAR SEAT SHOULDER BELT HANGER RH (w/ Rear No. 2 Seat)
HINT
Use the same procedure described for the LH side.
6. INSTALL REAR FLOOR FINISH SIDE PLATE LH (w/o Rear No. 2 Seat)
(a) Attach the claw and 2 guides to install the rear floor finish side plate.
(b) Install the 2 screws.
7. INSTALL REAR FLOOR FINISH SIDE PLATE RH (w/o Rear No. 2 Seat)
HINT
Use the same procedure described for the LH side.
8. INSTALL SIDE TRIM BOX LH (w/o Rear No. 2 Seat)
(a) Attach the 8 claws to install the side trim box.
(b) Install the 2 screws.
9. INSTALL SIDE TRIM BOX RH (w/o Rear No. 2 Seat)
HINT
Use the same procedure described for the LH side.
10. INSTALL REAR COMBINATION LIGHT SERVICE COVER LH
(a) Attach the 2 claws and 2 guides to install the rear combination light service cover.
11. INSTALL REAR COMBINATION LIGHT SERVICE COVER RH
HINT
Use the same procedure described for the LH side.
12. INSTALL QUARTER TRIM JACK COVER SUB-ASSEMBLY
(a) Attach the 3 claws and 2 guides to install the quarter trim jack cover.
13. INSTALL QUARTER TRIM COVER
HINT
Use the same procedure for the other quarter trim cover.
(a) Attach the 2 claws to install the quarter trim cover.
14. INSTALL REAR NO. 3 SIDE RAIL SPACER LH (w/ Rear No. 2 Seat)
(a) Attach the 2 claws to install the rear No. 3 side rail spacer.
15. INSTALL REAR NO. 3 SIDE RAIL SPACER RH (w/ Rear No. 2 Seat)
HINT
Use the same procedure described for the LH side.
16. INSTALL REAR NO. 2 SIDE RAIL SPACER LH (w/o Rear No. 2 Seat)
(a) Attach the 3 claws to install the rear No. 2 side rail spacer.
17. INSTALL REAR NO. 2 SIDE RAIL SPACER RH (w/o Rear No. 2 Seat)
HINT
Use the same procedure described for the LH side.
18. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH
(a) Attach the 4 claws to install the front shoulder belt anchor plate.
19. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH
HINT
Use the same procedure described for the LH side.
20. INSTALL ROOF HEADLINING ASSEMBLY
HINT
Before installing the roof headlining, move the front seats and rear No. 1 seat to the positions shown in the illustration.
(a) Place the roof headlining into the vehicle through the back door.
NOTICE:
Be careful not to damage the roof headlining when placing it in the cabin.
w/o Sliding Roof:
(1) Install the roof headlining with the 5 clips.
w/ Sliding Roof:
(1) Attach the 2 guides and 10 fasteners to install the roof headlining.
Text in Illustration
(b) Connect the connector and attach the clamp to the rear pillar RH.
(c) Connect the connector and attach the 2 clamps to the front pillar RH.
(d) Connect the connector and attach the 5 clamps to the front pillar LH.
(e) w/ Sliding Roof:
Connect the drive gear connector.
(f) w/ EC Mirror:
Connect the inner mirror connector.
21. INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY LH
(a) Attach the 3 clips to install the roof side rail garnish.
22. INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY RH
HINT
Use the same procedure described for the LH side.
23. INSTALL NO. 1 ROOM LIGHT ASSEMBLY Installation
24. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror) Installation
25. INSTALL MAP LIGHT ASSEMBLY Installation
26. INSTALL DRIVE MONITOR SWITCH Installation
27. INSTALL VISOR HOLDER
HINT
Use the same procedure for the other visor holder.
(a) Attach the 2 claws.
(b) Push in the visor holder to install it.
28. INSTALL VISOR ASSEMBLY LH
(a) Install the visor with the 2 screws.
29. INSTALL VISOR ASSEMBLY RH
HINT
Use the same procedure described for the LH side.
30. INSTALL VISOR BRACKET COVER LH
(a) Attach the 4 claws to install the visor bracket cover.
31. INSTALL VISOR BRACKET COVER RH
HINT
Use the same procedure described for the LH side.
32. INSTALL COAT HOOK
HINT
Use the same procedure for the other coat hook.
(a) Install the coat hook with the screw.
(b) Attach the claw to close the cover.
33. INSTALL REAR ASSIST GRIP ASSEMBLY
HINT
Use the same procedure for the other rear assist grip.
(a) Assemble the rear assist grip as shown in the illustration.
Install the rear assist grip.
34. INSTALL ASSIST GRIP SUB-ASSEMBLY
HINT
Use the same procedure for the other assist grip.
(a) Assemble the assist grip as shown in the illustration.
Install the assist grip.
35. INSTALL REAR WINDOW SIDE GARNISH ASSEMBLY LH
(a) Attach the 4 claws and 2 guides and pass the rear No. 1 seat outer belt floor anchor through the rear window side garnish.
(b) Attach the 7 clips and 4 guides to install the rear window side garnish.
36. INSTALL REAR WINDOW SIDE GARNISH ASSEMBLY RH
HINT
Use the same procedure described for the LH side.
37. INSTALL REAR NO. 2 WINDOW SIDE GARNISH ASSEMBLY LH
(a) w/ Rear No. 2 Seat:
(1) Attach the 7 claws and guide and pass the rear No. 2 seat outer belt floor anchor through the rear No. 2 window side garnish.
(b) Attach the 6 clips and guide to install the rear No. 2 window side garnish.
38. INSTALL REAR NO. 2 WINDOW SIDE GARNISH ASSEMBLY RH
HINT
Use the same procedure described for the LH side.
39. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
(a) w/o Rear No. 2 Seat:
(1) Pass the rear seatback lock control lever base through the deck trim side panel.
(2) Attach the 6 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel.
(3) Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel.
(4) Install the 3 bolts and 2 screws.
(5) Install the rear No. 1 seat outer belt floor anchor with the bolt.
Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)
(b) w/ Rear No. 2 Seat:
(1) Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel.
(2) Install the 3 bolts and 2 screws.
(3) Install the rear No. 1 seat outer belt floor anchor with the bolt.
Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)
(4) Install the rear No. 2 seat outer belt floor anchor with the bolt.
Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)
40. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
(a) w/o Rear No. 2 Seat:
(1) Connect the connector.
(2) Pass the rear seatback lock control lever base through the deck trim side panel.
(3) Attach the 6 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel.
(4) Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel.
(5) Install the 3 bolts and 2 screws.
(6) Install the rear No. 1 seat outer belt floor anchor with the bolt.
Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)
(b) w/ Rear No. 2 Seat:
(1) Connect the connector.
(2) Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel.
(3) Install the 3 bolts and 2 screws.
(4) Install the rear No. 1 seat outer belt floor anchor with the bolt.
Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)
(5) Install the rear No. 2 seat outer belt floor anchor with the bolt.
Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)
41. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM COVER
HINT
Use the same procedure described for the No. 1 luggage compartment trim cover.
42. INSTALL FRONT DECK SIDE TRIM COVER LH
(a) Attach the 2 claws to install the front deck side trim cover.
43. INSTALL FRONT DECK SIDE TRIM COVER RH
HINT
Use the same procedure described for the LH side.
44. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
HINT
Use the same procedure for the other No. 1 luggage compartment trim hook.
(a) Install the No. 1 luggage compartment trim hook by turning it clockwise.
45. INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER
HINT
Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.
(a) Attach the 3 claws to install the rear No. 1 seat outer lap belt anchor cover.
46. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)
(a) Attach the 4 claws to install the rear floor carpet.
47. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE
(a) Attach the 5 clips to install the rear floor mat rear support plate.
48. INSTALL INNER FLOOR SIDE RAIL SUB-ASSEMBLY (w/ Deck Board)
(a) Install the inner floor side rail with the 2 bolts and 4 nuts.
49. INSTALL DECK BOARD ASSEMBLY (w/ Deck Board)
(a) Attach the 2 guides to install the deck board.
(b) Install the 8 bolts.
50. INSTALL LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY LH (w/ Deck Board)
(a) Attach the 4 clips and 2 guides to install the luggage compartment side cover.
51. INSTALL LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY RH (w/ Deck Board)
HINT
Use the same procedure described for the LH side.
52. INSTALL REAR NO. 2 FLOOR BOARD ASSEMBLY (w/ Deck Board)
(a) Attach the 3 clips to install the rear No. 2 floor board.
53. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY (w/ Deck Board)
(a) Attach the 2 clips and 2 guides to install the No. 2 deck board.
54. INSTALL NO. 2 LUGGAGE COMPARTMENT TRIM COVER (w/ Deck Board, w/o Rear No. 2 Seat)
HINT
Use the same procedure for all No. 2 luggage compartment trim covers.
(a) Install the luggage hold belt striker and No. 2 luggage compartment trim cover with the bolt.
(b) Attach the 2 claws to close the cover.
55. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Deck Board)
(a) Attach the clip to install the No. 1 deck board.
56. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM COVER (w/o Deck Board)
HINT
Use the same procedure for the other No. 1 luggage compartment trim cover.
(a) Install the luggage hold belt striker and No. 1 luggage compartment trim cover with the bolt.
(b) Attach the 4 claws to close the cover.
57. INSTALL CENTER PILLAR GARNISH LH
(a) Pass the rear front seat outer belt floor anchor through the center pillar garnish.
(b) Attach the 2 clips and 2 guides to install the center pillar garnish.
(c) Install the bolt.
58. INSTALL CENTER PILLAR GARNISH RH
HINT
Use the same procedure described for the LH side.
59. INSTALL LOWER CENTER PILLAR GARNISH LH
(a) Attach the 4 claws and 2 clips to install the lower center pillar garnish.
(b) Install the front seat outer belt floor anchor with the bolt.
Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)
60. INSTALL LOWER CENTER PILLAR GARNISH RH
HINT
Use the same procedure described for the LH side.
61. INSTALL OUTER LAP BELT ANCHOR COVER
HINT
Use the same procedure for the other outer lap belt anchor cover.
(a) Attach the 3 claws to install the outer lap belt anchor cover.
62. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
(a) Align the paint mark on the rear door opening trim weatherstrip with the mark position on the vehicle and install the rear door opening trim weatherstrip as shown in the illustration.
Text in Illustration
63. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT
Use the same procedure described for the LH side.
64. INSTALL REAR DOOR SCUFF PLATE LH
(a) Attach the 3 clips, 6 claws and 2 guides to install the rear door scuff plate.
65. INSTALL REAR DOOR SCUFF PLATE RH
HINT
Use the same procedure described for the LH side.
66. INSTALL QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)
(a) Install the quarter scuff plate with the 2 bolts.
67. INSTALL QUARTER SCUFF PLATE RH (w/ Rear No. 2 Seat)
HINT
Use the same procedure described for the LH side.
68. INSTALL REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)
HINT
Use the same procedure for all rear No. 1 floor step covers.
(a) Attach the 2 claws to install the rear No. 1 floor step cover.
69. INSTALL FRONT PILLAR GARNISH LH
(a) Attach the 2 guides and 2 clips to install a new front pillar garnish.
NOTICE:
Do not reinstall a front pillar garnish that has been removed.
70. INSTALL FRONT PILLAR GARNISH RH
(a) Attach the 3 guides to install the front pillar garnish.
71. INSTALL NO. 1 ASSIST GRIP
(a) Attach the 2 claws to install the No. 1 assist grip.
(b) Install the 2 bolts.
72. INSTALL ASSIST GRIP PLUG
HINT
Use the same procedure for the other assist grip plug.
(a) Attach the 2 claws to install the assist grip plug.
73. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
(a) Align the paint mark on the front door opening trim weatherstrip with the mark position on the vehicle and install the front door opening trim weatherstrip as shown in the illustration.
Text in Illustration
74. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
HINT
Use the same procedure described for the LH side.
75. INSTALL COWL SIDE TRIM BOARD LH
(a) Attach the clip and claw to install the cowl side trim board.
76. INSTALL COWL SIDE TRIM BOARD RH
HINT
Use the same procedure described for the LH side.
77. INSTALL DOOR SCUFF PLATE ASSEMBLY LH
(a) Attach the 4 clips, 10 claws and 2 guides to install the door scuff plate.
78. INSTALL DOOR SCUFF PLATE ASSEMBLY RH
HINT
Use the same procedure described for the LH side.
79. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)
(a) Install the rear No. 2 seat assembly Installation.
80. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.